- 您现在的位置：买卖IC网 > PDF目录1915 > DS2482X-100+T (Maxim Integrated Products)IC MASTER I2C-1WIRE 1CH 9-WLP PDF资料下载
参数资料
| 型号： | DS2482X-100+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 9/24页 |
| 文件大小： | 0K |
| 描述： | IC MASTER I2C-1WIRE 1CH 9-WLP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 控制器类型： | I²C 总线控制器 |
| 接口： | I²C |
| 电源电压： | 2.9 V ~ 5.5 V |
| 电流 - 电源： | 750µA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 9-WFBGA，WLBGA |
| 供应商设备封装： | 9-WLP |
| 包装： | 带卷 (TR) |
Single-Channel 1-Wire Master
some time later the slave may refuse to accept data,
possibly because of an invalid command code or
parameter. In this case, the slave device does not
acknowledge any of the bytes that it refuses and
leaves SDA high. In either case, after a slave has
failed to acknowledge, the master first should gener-
ate a repeated START condition or a STOP condition
followed by a START condition to begin a new data
transfer.
Not Acknowledged by Master: At some time when
receiving data, the master must signal an end of
data to the slave device. To achieve this, the master
does not acknowledge the last byte that it has
received from the slave. In response, the slave
releases SDA, allowing the master to generate the
STOP condition.
Writing to the DS2482-100
To write to the DS2482-100, the master must access
the device in write mode, i.e., the slave address must
be sent with the direction bit set to 0. The next byte to
be sent is a command code, which, depending on the
command, may be followed by a command parameter.
The DS2482-100 acknowledges valid command codes
and expected/valid command parameters. Additional
bytes or invalid command parameters are never
acknowledged.
Reading from the DS2482-100
To read from the DS2482-100, the master must access
the device in read mode, i.e., the slave address must
be sent with the direction bit set to 1. The read pointer
determines the register that the master reads from. The
master can continue reading the same register over
and over again, without having to readdress the device,
e.g., to watch the 1WB changing from 1 to 0. To read
from a different register, the master must issue the Set
Read Pointer command and then access the DS2482-
100 again in read mode.
I2C Communication Examples
See Tables 4 and 5 for the I2C communication legend
and data direction codes.
Table 4. I2C Communication—Legend
SYMBOL
DESCRIPTION
S
START Condition
AD, 0
Select DS2482-100 for Write Access
AD, 1
Select DS2482-100 for Read Access
Sr
Repeated START Condition
P
STOP Condition
A
Acknowledged
A\
Not Acknowledged
(Idle)
Bus Not Busy
<byte>
Transfer of One Byte
DRST
Command “Device Reset”, F0h
SRP
Command “Set Read Pointer”, E1h
WCFG
Command “Write Configuration”, D2h
1WRS
Command “1-Wire Reset”, B4h
1WSB
Command “1-Wire Single Bit”, 87h
1WWB
Command “1-Wire Write Byte”, A5h
1WRB
Command “1-Wire Read Byte”, 96h
1WT
Command “1-Wire Triplet”, 78h
Table 5. Data Direction Codes
Master-to-Slave
Slave-to-Master
DS2482-100
Maxim Integrated
17
相关PDF资料 |
PDF描述 |
|---|---|
| DS2482X-101+T | IC MASTER I2C-1WIRE 1CH 9-WLP |
| DS2483Q+T | IC I2C TO 1WIRE BRIDGE 8TDFN |
| DS2490Y | IC BRIDGE CLIP USB TO 1-W 24SOIC |
| DS26303LN-75+A3 | IC LIU E1/T1/J1 3.3V 144-ELQFP |
| DS26324GNA2+ | IC INTERFACE LINE 16CH 256-CSBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2482X-101+T | 功能描述:接口 - 专用 1-Wire Master w/ Sleep Mode RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| DS2482X-101+U | 功能描述:接口 - 专用 SNGL-CH 1-WIRE MASTER w/ SLP MODE RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| DS2483 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Single-Channel 1-Wire Master with Adjustable Timing and Sleep Mode |
| DS2483Q+T | 功能描述:I2C 接口集成电路 Single-Channel 1-Wire Master RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16 |
| DS2483Q+U | 功能描述:I2C 接口集成电路 SINGLE-CH 1-WIRE MASTER RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16 |
发布紧急采购，3分钟左右您将得到回复。