- 您现在的位置：买卖IC网 > PDF目录20671 > DS2740BU+T&R (Maxim Integrated)IC CURRENT GAUGE(15BIT) 8UMAX PDF资料下载
参数资料
| 型号： | DS2740BU+T&R |
| 厂商： | Maxim Integrated |
| 文件页数： | 11/16页 |
| 文件大小： | 304K |
| 描述： | IC CURRENT GAUGE(15BIT) 8UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 3,000 |
| 功能： | 电流计（13 位） |
| 输入电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-uMAX |
| 包装： | 带卷 (TR) |
DS2740
Skip Net Address [CCh]. This command saves time when there is only one DS2740 on the bus by
allowing the bus master to issue a function command without specifying the address of the slave. If more
than one slave device is present on the bus, a subsequent function command can cause a data collision
when all slaves transmit data at the same time.
Search Net Address [F0h]. This command allows the bus master to use a process of elimination to
identify the 1-Wire net addresses of all slave devices on the bus. The search process involves the
repetition of a simple three-step routine: read a bit, read the complement of the bit, then write the desired
value of that bit. The bus master performs this simple three-step routine on each bit location of the net
address. After one complete pass through all 64 bits, the bus master knows the address of one device. The
remaining devices can then be identified on additional iterations of the process. See Chapter 5 of the Book
of DS19xx i
Button
?/DIV>
Standards for a comprehensive discussion of a net address search, including an actual
example. (This publication can be found on the Maxim/Dallas Semiconductor website at www.maxim-
ic.com.)
Resume [A5h]. This command increases data throughput in multidrop environments where the DS2740
needs to be accessed several times. Resume is similar to the Skip Net Address command in that the 64-
bit net address does not have to be transmitted each time the DS2740 is accessed. After successfully
executing a Match Net Address command or Search Net Address command, an internal flag is set in the
DS2740. When the flag is set, the DS2740 can be repeatedly accessed through the Resume command
function. Accessing another device on the bus clears the flag, thus preventing two or more devices from
simultaneously responding to the Resume command function.
FUNCTION COMMANDS
After successfully completing one of the net address commands, the bus master can access the features of
the DS2740 with any of the function commands described in the following paragraphs and summarized in
Table 4. The name of each function is followed by the 8-bit opcode for that command in square brackets.
Read Data [69h, XX]. This command reads data from the DS2740 starting at memory address XX. The
LSb of the data in address XX is available to be read immediately after the MSb of the address has been
entered. Because the address is automatically incremented after the MSb of each byte is received, the LSb
of the data at address XX + 1 is available to be read immediately after the MSb of the data at address XX.
If the bus master continues to read beyond address FFh, the DS2740 starts over at address 00h.
Addresses labeled Reserved in the memory map contain undefined data. The Read Data command can
be terminated by the bus master with a reset pulse at any bit boundary.
Write Data [6Ch, XX]. This command writes data to the DS2740 starting at memory address XX. The
LSb of the data to be stored at address XX can be written immediately after the MSb of address has been
entered. Because the address is automatically incremented after the MSb of each byte is written, the LSb
to be stored at address XX + 1 can be written immediately after the MSb to be stored at address XX. If
the bus master continues to write beyond address FFh, the DS2740 starts over writing at address 00h.
Writes to read-only addresses and reserved addresses are ignored. Incomplete bytes are not written. See
the Memory section for more details.
i
Button is a registered trademark of Dallas Semiconductor.
11 of 16
相关PDF资料 |
PDF描述 |
|---|---|
| MAX4995AATA+T | IC SWITCH CURRENT LIMIT 8TDFN |
| TC1303B-VS0EUNTR | IC REG DL BCK/LINEAR SYNC 10MSOP |
| TC1303B-VS0EUN | IC REG DL BCK/LINEAR SYNC 10MSOP |
| B160-E3/5AT | DIODE SCHOTTKY 1A 60V SMA |
| TC1303B-PI0EUNTR | IC REG DL BCK/LINEAR SYNC 10MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2740EVKIT+ | 制造商:Maxim Integrated Products 功能描述:HIGH-PRECISION COULOMB COUNTER - Boxed Product (Development Kits) |
| DS2740K | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| DS2740U | 制造商:Maxim Integrated Products 功能描述:HI PRECISION COUL CNTR UMAX(USOP)-8 - Rail/Tube |
| DS2740U/R | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:High-Precision Coulomb Counter |
| DS2740U/T | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:High-Precision Coulomb Counter |
发布紧急采购，3分钟左右您将得到回复。