- 您现在的位置：买卖IC网 > PDF目录16239 > DS2781E+ (Maxim Integrated Products)IC FUEL GAUGE BATT 8TSSOP PDF资料下载
参数资料
| 型号： | DS2781E+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 13/31页 |
| 文件大小： | 0K |
| 描述： | IC FUEL GAUGE BATT 8TSSOP |
| 产品培训模块： | 1-Wire Communications Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 功能： | 燃料，电量检测计/监控器 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 2.5 V ~ 10 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 8-TSSOP |
| 包装： | 管件 |
| 产品目录页面： | 1436 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
DS2781
MODELING CELL STACK CHARACTERISTICS
In order to achieve reasonable accuracy in estimating remaining capacity, the cell stack performance
characteristics over temperature, load current and charge termination point must be considered. Since the behavior
of Li-ion cells is non-linear, these characteristics must be included in the capacity estimation to achieve an
acceptable level of accuracy in the capacity estimation. The FuelPack? method used in the DS2781 is described
in general in Application Note AN131: Lithium-Ion Cell Fuel Gauging with Dallas Semiconductor Battery Monitor
ICs . To facilitate efficient implementation in hardware, a modified version of the method outlined in AN131 is used
to store cell characteristics in the DS2781. Full and empty points are retrieved in a look-up process which re-traces
piece-wise linear model consisting of three model curves named Full, Active Empty and Stand-by Empty. Each
model curve is constructed with 5 line segments, numbered 1 through 5. Above +40°C, the segment 5 model
curves extend infinitely with zero slope, approximating the nearly flat change in capacity of Li-Ion cells at
temperatures above +40°C. Segment 4 of each model curves originates at +40°C on its upper end and extends
downward in temperature to the junction with segment 3. Segment 3 joins with segment 2, which in turn joins with
segment 1. Segment 1 of each model curve extends from the junction with segment 2 to infinitely colder
temperatures. Segment slopes are stored as μVh ppm change per oC. The three junctions or breakpoints that join
the segments (labeled TBP12, TBP23 and TBP34 in figure 12) are programmable in +1°C increments from -128°C
to +40°C. They are stored in two’s complement format in locations 0x7C, 0x7D, and 0x7E, respectively. The slope
or derivative for segments 1, 2, 3, and 4 are also programmable. One the lower (cold) end of each model curve,
segment 1 extends from breakpoint TBP12 to infinitely to colder temperatures.
Figure 12. Cell Model Example Diagram
Segment 1
Seg. 2
Seg. 3
Seg. 4
Seg. 5
100%
FULL
Derivative
[ppm / C]
Active
Empty
Stand-by
Empty
Cell Characterization
data points
TBP12
TBP23
TBP34
40C
Full: The Full curve defines how the full point of a given cell stack depends on temperature for a given charge
termination. The charge termination method used in the application is used to determine the table values. The
DS2781 reconstructs the Full line from cell characteristic table values to determine the Full capacity of the battery
at each temperature. Reconstruction occurs in one-degree temperature increments. Full values are stored as ppm
change per oC. For example if a cell had a nominal capacity of 1051mAh at 40oC, a full value of 1031mAh at 18oC
(TBP34) and 1009mAh at 0oC (TBP23), the slope for segment 3 would be:
((1031mAh – 1009mAh) / (1051mAh / 1M)) / (18oC - 0oC) = 1163ppm/oC
1 LSB of the slope registers equals 61ppm so the Full Segment 3 Slope register (location 0x6Dh) would be
programmed with a value of 0x13h. Each slope register has a dynamic range 0ppm to 15555ppm.
FuelPack is a trademark of Maxim Integrated Products, Inc.
13 of 31
相关PDF资料 |
PDF描述 |
|---|---|
| EBM15DSEF-S243 | CONN EDGECARD 30POS .156 EYELET |
| SLP332M050C3P3 | CAP ALUM 3300UF 50V 20% SNAP |
| REC15-2415SZ/H3 | CONV DC/DC 15W 24VIN 15VOUT |
| RBM18DSEF-S13 | CONN EDGECARD 36POS .156 EXTEND |
| REC15-245.1SZ/H3 | CONV DC/DC 15W 24VIN 5.1VOUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2781E+ | 功能描述:电池管理 1-2 Cell Stand-Alone Fuel Gauge RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| DS2781E+T&R | 制造商:Maxim Integrated Products 功能描述:FUEL GAUGE 制造商:Maxim Integrated Products 功能描述:STANDALONE FUEL GAUGE IC 8TSSOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC FUEL GAUGE BATT 8TSSOP |
| DS2781E+T&R | 功能描述:电池管理 1-2 Cell Stand-Alone Fuel Gauge RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| DS2781E+TR | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:1-Cell or 2-Cell Standalone Fuel Gauge IC |
| DS2781E-C1+T&R | 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。