参数资料
型号: DS2781E+
厂商: Maxim Integrated Products
文件页数: 24/31页
文件大小: 0K
描述: IC FUEL GAUGE BATT 8TSSOP
产品培训模块: 1-Wire Communications
Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 1
功能: 燃料,电量检测计/监控器
电池化学: 锂离子(Li-Ion)、锂聚合物(Li-Pol)
电源电压: 2.5 V ~ 10 V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 8-TSSOP(0.173",4.40mm 宽)
供应商设备封装: 8-TSSOP
包装: 管件
产品目录页面: 1436 (CN2011-ZH PDF)
DS2781
In the circuit in Figure 23, the shift register bits are initialized to 0. Then, starting with the least significant bit of the
family code, one bit at a time is shifted in. After the 8th bit of the family code has been entered, then the serial
number is entered. After the 48th bit of the serial number has been entered, the shift register contains the CRC
value.
Figure 23. 1-Wire CRC Generation Block Diagram
INPUT
MSb
XOR
XOR
LSb
XOR
HARDWARE CONFIGURATION
Because the 1-Wire bus has only a single line, it is important that each device on the bus be able to drive it at the
appropriate time. To facilitate this, each device attached to the 1-Wire bus must connect to the bus with open-drain
or tri-state output drivers. The DS2781 uses an open-drain output driver as part of the bidirectional interface
circuitry shown in Figure 24. If a bidirectional pin is not available on the bus master, separate output and input pins
can be connected together.
The 1-Wire bus must have a pullup resistor at the bus-master end of the bus. For short line lengths, the value of
this resistor should be approximately 5k Ω . The idle state for the 1-Wire bus is high. If, for any reason, a bus
transaction must be suspended, the bus must be left in the idle state to properly resume the transaction later. If the
bus is left low for more than 120 μ s (16 μ s for overdrive speed), slave devices on the bus begin to interpret the low
period as a reset pulse, effectively terminating the transaction.
The DS2781 can operate in two communication speed modes, standard and overdrive. The speed mode is
determined by the input logic level of the OVD pin with a logic 0 selecting standard speed and a logic 1 selecting
overdrive speed. The OVD pin must be at a stable logic level of 0 or 1 before initializing a transaction with a reset
pulse. All 1-Wire devices on a multinode bus must operate at the same communication speed for proper operation.
1-Wire timing for both standard and overdrive speeds are listed in the Electrical Characteristics: 1-Wire Interface
tables.
Figure 24. 1-Wire Bus Interface Circuitry
BUS MASTER
Rx
Vpullup
(2.0V to 5.5V)
4.7k Ω
DS2781 1-WIRE PORT
RX
Tx
RX = RECEIVE
TX = TRANSMIT
24 of 31
0.2 μ A
(typ)
100 Ω
MOSFET
TX
相关PDF资料
PDF描述
EBM15DSEF-S243 CONN EDGECARD 30POS .156 EYELET
SLP332M050C3P3 CAP ALUM 3300UF 50V 20% SNAP
REC15-2415SZ/H3 CONV DC/DC 15W 24VIN 15VOUT
RBM18DSEF-S13 CONN EDGECARD 36POS .156 EXTEND
REC15-245.1SZ/H3 CONV DC/DC 15W 24VIN 5.1VOUT
相关代理商/技术参数
参数描述
DS2781E+ 功能描述:电池管理 1-2 Cell Stand-Alone Fuel Gauge RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel
DS2781E+T&R 制造商:Maxim Integrated Products 功能描述:FUEL GAUGE 制造商:Maxim Integrated Products 功能描述:STANDALONE FUEL GAUGE IC 8TSSOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC FUEL GAUGE BATT 8TSSOP
DS2781E+T&R 功能描述:电池管理 1-2 Cell Stand-Alone Fuel Gauge RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel
DS2781E+TR 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:1-Cell or 2-Cell Standalone Fuel Gauge IC
DS2781E-C1+T&R 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel