- 您现在的位置：买卖IC网 > Datasheet目录322 > DS28DG02E-3C+T (Maxim Integrated)IC EEPROM 2KBIT 2MHZ 28TSSOP Datasheet资料下载
参数资料
| 型号： | DS28DG02E-3C+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 29/34页 |
| 文件大小： | 0K |
| 描述： | IC EEPROM 2KBIT 2MHZ 28TSSOP |
| 标准包装： | 2,500 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 2K (256 x 8) |
| 速度： | 2MHz |
| 接口： | SPI 3 线串行 |
| 电源电压： | 2.2 V ~ 5.25 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 28-SOIC（0.173"，4.40mm 宽）裸露焊盘 |
| 供应商设备封装： | 28-TSSOP 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页
DS28DG02: 2Kb SPI EEPROM with PIO, RTC, Reset, Battery Monitor, and Watchdog
Figure 21. PIO Write Access Timing, Low-Current Mode
SCK
This edge clocks in the last (LS)
bit of the new PIO data byte.
The t OT timing reference is 80%
or 20% of maximum current.
This edge starts the
transfer of the new data to
the PIO pins. See Note.
t OT
PIOn
Note : In SPI Mode (1,1) there is no falling SCK edge for the last bit of the last byte sent to the device; in this case,
the transfer to the PIO is initiated with the rising edge of CSZ. This note also applies to the high-current mode.
Writing in High-Current Mode
When writing to PIOs in high-current mode, the state change is triggered by the falling edge of SCK after the last bit
of the new PIO state is shifted into the DS28DG02. The PIOs change their state sequentially, as shown in Figure
22, beginning with PIO0 or PIO8, respectively, depending on the address. A PIO that is changing its state is first tri-
stated for 2μs maximum. This 2μs delay also applies to PIOs configured as input and to PIOs configured as output
that do not change their state. The state transition of PIOs in high-current mode is slew-rate controlled to prevent
immediate full current-drive or release. Each pin’s slew-rate circuit is designed to ramp up to the full current drive or
release over the course of 1 μ s. The t OT value specified for high-current mode is valid when updating all 12 PIOs in
a single write access. In this case there is an extra 1μs maximum delay when transitioning from PIO7 to PIO8. In
high-current mode, the automatic alternation between groups of PIOs does not apply; another WREN and WRITE
sequence is necessary to update the PIO states again.
Figure 22. PIO Write Access Timing, High-Current Mode
SCK
This edge clocks in the last (LS)
bit of the new PIO data byte.
Tri-stated
2μs
1μs max.
max.
PIO0 (PIO8)
PIO1 (PIO9)
PIO2 (PIO10)
PIO3 (PIO11)
29 of 34
相关PDF资料 |
PDF描述 |
|---|---|
| DS28E04S-100+T | IC EEPROM 4KBIT 16SOIC |
| DS28EC20+T | IC EEPROM 20KBIT TO92-3 |
| DS301X | KWIK-CHG DESIGNATION STRIP SGL |
| DS3030W-100# | IC NVSRAM 256KBIT 100NS 256BGA |
| DS3045W-100# | IC NVSRAM 1MBIT 100NS 256BGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS28DG02EVKIT | 功能描述:存储器 IC 开发工具 RoHS:否 制造商:STMicroelectronics 产品:Reference Boards 工具用于评估:M24LR64-R 存储容量:64 kbit 存储类型:EEPROM 工作电源电压:1.8 V to 5.5 V |
| DS28DG02G-3C+ | 功能描述:电可擦除可编程只读存储器 2Kb SPI 电可擦除可编程只读存储器 w/PIO RTC/Rst/Bat Mtr/Wtdg RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| DS28DG02G-3C+T | 功能描述:电可擦除可编程只读存储器 2Kb SPI 电可擦除可编程只读存储器 w/PIO RTC/Rst/Bat Mtr/Wtdg RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| DS28E01-100 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:带SHA-1引擎保护的1K位1-Wire EEPROM |
| DS28E01-100_12 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:1Kb Protected 1-Wire EEPROM with SHA-1 Engine |
发布紧急采购，3分钟左右您将得到回复。