- 您现在的位置：买卖IC网 > PDF目录11562 > DS3148 (Maxim Integrated Products)IC 8CH DS3/3 FRAMER 349-BGA PDF资料下载
参数资料
| 型号： | DS3148 |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 65/89页 |
| 文件大小： | 0K |
| 描述： | IC 8CH DS3/3 FRAMER 349-BGA |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 控制器类型： | DS3/E3 调帧器 |
| 接口： | LIU |
| 电源电压： | 3.135 V ~ 3.465 V |
| 电流 - 电源： | 640mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 349-BGA 裸露焊盘 |
| 供应商设备封装： | 349-HCBGA（27x27） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页当前第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页
DS3146/DS3146/DS31412 6-/8-/12-Channel DS3/E3 Framers
68 of 89
8. OPERATION DETAILS
8.1 Reset
The DS314x devices must be reset by activating the
JTRST and RST pins after the power supply has settled and
the input clocks have stabilized to their normal operating conditions. The
JTRST pin can be permanently wired low
if desired. After reset, all read/write control register bits are reset to 0 except for RDATH and TUA1, which are set
to 1. The reset states of the device pins are as follows:
E3 mode is enabled.
The LIU interface is in dual-rail (POS/NEG) mode with HDB3 encoding and decoding enabled.
TPOS and TNEG transmit an unframed all-ones signal (E3 AIS) on the transmit LIU interface.
RDAT is forced to a logic 1 level to present an unframed all-ones signal (E3 AIS) on the receive system
interface.
TCLK is a noninverted, delayed version of TICLK.
ROCLK is a noninverted, delayed version or RCLK.
TSOF is an active-high input pin.
RSOF, RLOS, and ROOF are active high.
TDEN/TGCLK is in the TDEN (data enable) mode and is active high.
RDEN/RGCLK is in the RDEN (data enable) mode and is active high.
JTDO is tri-stated.
8.2 DS3 and E3 Mode Configuration
In all modes, the TUA1 bit in the MC1 register and RDATH bit in the MC4 register must be cleared. These bits are
set to 1 at reset to generate an unframed all-ones (E3 AIS) signal on both the transmit LIU interface (TPOS/TNEG)
and the receive system interface (RDAT).
E3 Mode
Default framer operation after reset is E3 mode. To begin operation in E3 mode after reset, clear the TUA1 bit in
the MC1 register and clear the RDATH bit in the MC4 register. A 34.368MHz clock must be applied to the TICLK
pin.
DS3 M23 Mode
To change framer operation after reset to DS3 M23 mode, set the DS3M bit to 1 in the T3E3CR1 register, clear the
TUA1 bit in the MC1 register, and clear the RDATH bit in the MC4 register. A 44.736MHz clock must be applied to
the TICLK pin.
DS3 C-Bit Parity Mode
To change framer operation after reset to DS3 C-Bit Parity mode, set the DS3M and CBEN bits to 1 in the
T3E3CR1 register, clear the TUA1 bit in the MC1 register, and clear the RDATH bit in the MC4 register. A
44.736MHz clock must be applied to the TICLK pin.
8.3 LIU and System Interface Configuration
LIU Interface
After reset the default LIU interface format is dual-rail (POS/NEG) with B3ZS/HDB3 encoding and decoding
enabled. To change framer operation after reset to binary (NRZ) format with B3ZS/HDB3 encoding and decoding
disabled (disabled in the framer but should be enabled in the LIU), set the BIN bit to 1 in the MC1 register.
System Interface
After reset the TDEN/TGCLK and RDEN/RGCLK pins default to data enable behavior (TDEN, RDEN) and the
TSOF pin defaults to being an input. If gapped clock behavior is desired, set the TDENMS bit tin the MC3 register
and/or the RDENMS bit in the MC4 register. To configure TSOF as an output pin, set the TSOFC bit to 1 in the
MC3 register.
相关PDF资料 |
PDF描述 |
|---|---|
| DS21FT42 | IC FRAMER T1 4X3 12CH 300-BGA |
| V375C24M75BL3 | CONVERTER MOD DC/DC 24V 75W |
| V375C24M75BL2 | CONVERTER MOD DC/DC 24V 75W |
| DS21FF42N+ | IC FRAMER T1 4X4 16CH 300-BGA |
| DS21FT42N | IC FRAMER T1 4X3 12CH IND 300BGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS3148N | 功能描述:网络控制器与处理器 IC 8 Port DS3/E3 Framer RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS315 | 制造商:Hubbell Wiring Device-Kellems 功能描述:SWITCH, DECO SER, 3W, 15A 120/277V, BR |
| DS3150 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:3.3V, DS3/E3/STS-1 Line Interface Unit |
| DS3150DK | 功能描述:网络开发工具 DS3150 Dev Kit RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V |
| DS3150G | 功能描述:IC LIU T3/E3/STS-1 49-BGA RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:25 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:4.5 V ~ 5.5 V 安装类型:通孔 封装/外壳:16-DIP（0.300"，7.62mm） 供应商设备封装:16-PDIP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。