参数资料
| 型号： | DS33Z41DK |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/44页 |
| 文件大小： | 0K |
| 描述： | KIT DESIGN FOR DS33Z41 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 主要目的： | 接口，以太网 |
| 已用 IC / 零件： | DS33Z41 |
| 已供物品： | 板，串行卡，CD |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
DS33Z41DK
BASIC OPERATION
Powering Up the Design Kit
?
?
?
Attach DS21458 resource card to main board.
Connect PCB 3.3V and GND banana plugs to power supply. At power-up the system should draw
approximately 1A.
Set switches for software mode as described in Table 2 (short description follows).
? Top left bank: All low, except for MODEC0, which is high.
? Top right bank: A2, A1, A0 in mid position, SCANTRI low
? Bottom Bank: All high (AFCS, FULLDS, H1OS)
General
?
Upon power-up, the processor FPGA Status LEDs (DS43 green) will be lit. Interrupt LEDs (DS44 red) will not
be lit. DS33Z11 Queue overflow LEDs (DS39 red) will not be lit. PHY LINK LED (DS06 green) should be lit if
the Ethernet is connected.
Following are several basic system initializations. These initializations assume that there are two boards present
(DS33Z41 and / or DS33R41). A note is provided below to assist with using a system that only contains one board.
Basic DS33Z41 Initialization (Used for All Quick Setups)
This section covers four basic methods for configuring the DS33Z41. Any one of these initializations can be used
with the following Quick Setup examples:
1. Upon power-up, the on-board device driver provides a basic configuration for the DS33Z41 and attached
serial cards. This enables traffic to pass from the Ethernet port to the serial port. Consult the device driver
documentation for further details. Device driver behavior is dependant upon jumper settings, which are
detailed in Table 2.
2. Launch ChipView.exe and select Register View. When prompted for a definition file, pick the file named
DS33Z41.def . Following this load the definition file named DS21458RC_FPGA.def
3. Hardware Mode is not available with this DK
4. EEPROM mode is not available with this DK.
5. Ethernet Traffic generation and analysis:
a. Using a patch cable, connect the Ethernet connector to an ordinary PC, or network test equipment.
This should cause the link LED to turn on.
b. Although ping is mentioned it is *not* recommended. The ping command goes through the
computers TCPIP stack, and will sometimes will not be sent out the PCs network connector (i.e. if
the PCs ARP cache is out of date). Additionally ping requires two PCs, as a PC can not ping itself
(a local ping gets sent to ‘localhost’ instead of out the connector). With that said – ping is still a
valuable test once the prototyping stage is complete.
c. Generation and capture of arbitrary (raw) packets can be accomplished using CommView. A time-
limited demo is available at the website www.tamos.com/products/commview .
d. Ethereal is an excellent (and free) packet capture utility. Download is available at
e. Adding additional Ethernet ports to a PC is rather simple when a USB-to-Ethernet adapter is used.
This allows for end-to-end testing using a single PC. When using two adapters the PC will have a
different IP address for each adapter. Test equipment will allow selection of either adapter.
Operating system based network traffic will be sent out the default adapter, usually this is the
adapter that has recently had connection to a real network.
10 of 44
相关PDF资料 |
PDF描述 |
|---|---|
| DS9097E# | COM PORT ADAPTER |
| DS9097U-E25# | ADAPTER COM PORT RS232 DB-25 |
| DS9490R# | IC BRIDGE USB TO 1-WIRE RJ11 |
| DST1E1DK | KIT DESIGN SCT T1/E1 DS21X5Y |
| DV103003 | KIT DEV MICROID 13.56MHZ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS33Z44 | 功能描述:网络控制器与处理器 IC Quad Ethernet Mapper RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS33Z44+ | 功能描述:网络控制器与处理器 IC Quad Ethernet Mapper RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS33Z44DK | 功能描述:以太网开发工具 DS33Z44 Dev Kit RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压: |
| DS33ZH11 | 功能描述:网络控制器与处理器 IC 10/100 ENETXPORT HMODE MAP IND RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS33ZH11+ | 功能描述:网络控制器与处理器 IC 10/100 ENETXPORT HMODE MAP IND RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。