- 您现在的位置：买卖IC网 > PDF目录2068 > DS3510T+ (Maxim Integrated Products)IC I2C GAMMA/VCOM BUFF 48-TQFN PDF资料下载
参数资料
| 型号： | DS3510T+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/17页 |
| 文件大小： | 0K |
| 描述： | IC I2C GAMMA/VCOM BUFF 48-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 209 |
| 应用： | TFT-LCD 面板：伽玛缓冲器，VCOM 驱动器 |
| 输出类型： | 满摆幅 |
| 电路数： | 10 |
| 电流 - 电源： | 6.7mA |
| 电流 - 输出 / 通道： | 4mA |
| 电压 - 电源，单路/双路(±)： | 9 V ~ 15 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-WFQFN 裸露焊盘 |
| 供应商设备封装： | 48-TQFN-EP（7x7） |
| 包装： | 管件 |
Byte write: A byte write consists of 8 bits of information
transferred from the master to the slave (most signifi-
cant bit first) plus a 1-bit acknowledgment from the
slave to the master. The 8 bits transmitted by the mas-
ter are done according to the bit write definition and the
acknowledgment is read using the bit read definition.
Byte read: A byte read is an 8-bit information transfer
from the slave to the master plus a 1-bit ACK or NACK
from the master to the slave. The 8 bits of information
that are transferred (most significant bit first) from the
slave to the master are read by the master using the bit
read definition above, and the master transmits an ACK
using the bit write definition to receive additional data
bytes. The master must NACK the last byte read to ter-
minate communication so the slave will return control of
SDA to the master.
Slave Address Byte: Each slave on the I2C bus
responds to a slave address byte sent immediately fol-
lowing a start condition. The slave address byte con-
tains the slave address in the most significant 7 bits
and the R/W bit in the least significant bit.
The DS3510’s slave address is determined by the state
of the A0 address pin as shown in Figure 5. An address
pin connected to GND results in a 0 in the correspond-
ing bit position in the slave address. Conversely, an
address pin connected to VCC results in a 1 in the cor-
responding bit position.
When the R/W bit is 0 (such as in C0h), the master is
indicating it will write data to the slave. If R/W is set to a
1, (C1h in this case), the master is indicating it wants to
read from the slave.
If an incorrect (non-matching) slave address is written,
the DS3510 will assume the master is communicating
with another I2C device and ignore the communication
until the next start condition is sent.
Memory address: During an I2C write operation to the
DS3510, the master must transmit a memory address to
identify the memory location where the slave is to store
the data. The memory address is always the second
byte transmitted during a write operation following the
slave address byte.
I2C Communication
Writing a single byte to a slave: The master must gen-
erate a START condition, write the slave address byte
(R/W = 0), write the memory address, write the byte of
data, and generate a STOP condition. Remember the
master must read the slave’s acknowledgment during
all byte write operations.
When writing to the DS3510 (and if LD = 1), the DAC will
adjust to the new setting once it has acknowledged the
new data that is being written, and the EEPROM (used to
make the setting nonvolatile) will be written following the
STOP condition at the end of the write command.
Writing multiple bytes to a slave: To write multiple
bytes to a slave in one transaction, the master gener-
ates a START condition, writes the slave address byte
(R/W = 0), writes the memory address, writes up to 8
data bytes, and generates a STOP condition. The
DS3510 is capable of writing 1 to 8 bytes (1 page or
row) in a single write transaction. This is internally con-
trolled by an address counter that allows data to be
written to consecutive addresses without transmitting a
memory address before each data byte is sent. The
address counter limits the write to one 8-byte page
(one row of the memory map). The first page begins at
address 00h and subsequent pages begin at multiples
of 8 (08h, 10h, 18h, etc). Attempts to write to additional
pages of memory without sending a STOP condition
between pages results in the address counter wrap-
ping around to the beginning of the present row. To
prevent address wrapping from occurring, the master
must send a STOP condition at the end of the page,
then wait for the bus-free or EEPROM-write time to
elapse. Then the master can generate a new START
condition and write the slave address byte (R/W = 0)
and the first memory address of the next memory row
before continuing to write data.
Acknowledge polling: Any time a EEPROM byte is
written, the DS3510 requires the EEPROM write time
(tW) after the STOP condition to write the contents of
the byte to EEPROM. During the EEPROM write time,
the device will not acknowledge its slave address
because it is busy. It is possible to take advantage of
this phenomenon by repeatedly addressing the
DS3510, which allows communication to continue as
soon as the DS3510 is ready. The alternative to
acknowledge polling is to wait for a maximum period of
tW to elapse before attempting to access the device.
DS3510
I2C Gamma and VCOM Buffer with EEPROM
______________________________________________________________________________________
15
相关PDF资料 |
PDF描述 |
|---|---|
| DS3514T+T&R | IC I2C GAMMA/VCOM BUFF 48-TQFN |
| EL1881CS-T13 | IC VIDEO SYNC SEPARATOR 8-SOIC |
| EL1883IS-T13 | IC VID SYNC SEPARATOR HORZ 8SOIC |
| EL2250CS-T13 | IC OP AMP DUAL 125MHZ 8-SOIC |
| EL4093CSZ-T7 | IC VIDEO AMP 300MHZ 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS3510T+ | 功能描述:LCD Gamma缓冲器 I2C Gamma & VCOM Buffer w/EEPROM RoHS:否 制造商:Maxim Integrated 输入补偿电压: 转换速度: 电源电压-最大:20 V 电源电压-最小:9 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-38 封装:Tube |
| DS3510T+T&R | 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:10 CH GAMMA+VCOM 8BIT 48 TQFN T&R L - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC I2C GAMMA/VCOM BUFF 48-TQFN |
| DS3510T+T&R | 功能描述:LCD Gamma缓冲器 I2C Gamma & VCOM Buffer w/EEPROM RoHS:否 制造商:Maxim Integrated 输入补偿电压: 转换速度: 电源电压-最大:20 V 电源电压-最小:9 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-38 封装:Tube |
| DS3510T+TR | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:I2C Gamma and VCOM Buffer with EEPROM |
| DS3511MP000 | 制造商:Thomas & Betts 功能描述:30A,PLG,4P5W,MG,511,220/115V |
发布紧急采购，3分钟左右您将得到回复。