- 您现在的位置：买卖IC网 > PDF目录19309 > DS3881E+T&R/C (Maxim Integrated)IC AUTO CCFL CTRLR 1CH 24-TSSOP PDF资料下载
参数资料
| 型号： | DS3881E+T&R/C |
| 厂商： | Maxim Integrated |
| 文件页数： | 15/28页 |
| 文件大小： | 0K |
| 描述： | IC AUTO CCFL CTRLR 1CH 24-TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1,000 |
| 类型： | CCFL 控制器 |
| 频率： | 40 ~ 100 kHz |
| 电流 - 电源： | 12mA |
| 电源电压： | 4.75 V ~ 5.25 V |
| 工作温度： | -40°C ~ 105°C |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 24-TSSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
Single-Channel Automotive CCFL Controller
Figure 8 shows a flowchart of how the DS3881 controls
and monitors each lamp. The steps are as follows:
1) Supply Check—The lamps do not turn on unless the
DS3881 supply voltage is above 4.3V and the volt-
age at the supply voltage monitors, SVML and SVMH,
are respectively above 2.0V and below 2.0V.
2) Strike Lamp—When both the DS3881 and the DC
inverter supplies are at acceptable levels, the
DS3881 attempts to strike the lamp. The DS3881
slowly ramps up the MOSFET gate duty cycle until
the lamp strikes. The controller detects that the lamp
has struck by detecting current flow in the lamp,
detected by the LCM1 pin. If during the strike ramp,
the maximum allowable voltage is reached on the
OVD1 pin, the controller stops increasing the MOS-
FET gate duty cycle to keep from overstressing the
system. The DS3881 goes into a fault handling state
(step 4) if the lamp has not struck after the timeout
period as defined by the LST0 and LST1 control bits
in the SSP1 register. If an overvoltage event is detect-
ed during the strike attempt, the DS3881 disables the
MOSFET gate drivers and go into the fault handling
state.
3) Run Lamp—Once the lamp is struck, the DS3881
adjusts the MOSFET gate duty cycle to optimize the
lamp current. The gate duty cycle is always con-
strained to keep the system from exceeding the
maximum allowable lamp voltage. The lamp current
sampling rate is user-selectable using the LSR0 and
LSR1 bits in CR2. If lamp current ever drops below the
lamp out reference point for the period as defined by
the LST0 and LST1 control bits in the SSP1 register,
then the lamp is considered extinguished. In this case,
the MOSFET gate drivers are disabled and the device
moves to the fault handling stage.
4) Fault Handling—During fault handling, the DS3881
performs an optional (user-selectable) automatic
retry to attempt to clear all faults except a lamp over-
current. The automatic retry makes 14 additional
attempts to rectify the fault before declaring the
channel in a fault state and permanently disabling
the channel. Between each of the 14 attempts, the
controller waits 1024 lamp cycles. In the case of a
lamp overcurrent, the DS3881 instantaneously
declares the channel to be in a fault state and per-
manently disables the channel. Once a fault state is
entered, the channel remains in that state until one of
the following occurs:
? V CC drops below the UVLO threshold.
? The SVML or SVMH thresholds are crossed.
? The PDN pin goes high.
? The PDNE software bit is written to a logic 1.
? The channel is disabled by the CH1D control bit.
____________________________________________________________________
15
相关PDF资料 |
PDF描述 |
|---|---|
| VI-212-EU | CONVERTER MOD DC/DC 15V 200W |
| RMM28DTAD | CONN EDGECARD 56POS R/A .156 SLD |
| VE-B1B-CV-F4 | CONVERTER MOD DC/DC 95V 150W |
| GEM08DSXS | CONN EDGECARD 16POS DIP .156 SLD |
| VE-B1B-CV-F3 | CONVERTER MOD DC/DC 95V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS3882 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Dual-Channel Automotive CCFL Controller |
| DS3882_10 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Dual-Channel Automotive CCFL Controller |
| DS3882E | 制造商:Maxim Integrated Products 功能描述:CAR DUAL CCFL CONTROL TSSOP - 28 - Rail/Tube |
| DS3882E/T&R | 制造商:Maxim Integrated Products 功能描述:CAR DUAL CCFL CTRL TSSOP-28 T&R - Tape and Reel |
| DS3882E+ | 功能描述:IC CCFL CNTRLR DUAL 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 照明，镇流器控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:CCFL 控制器 频率:40 ~ 80 kHz 电流 - 电源:5mA 电流 - 输出:- 电源电压:4.5 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) 其它名称:90-3991V+V01 |
发布紧急采购，3分钟左右您将得到回复。