- 您现在的位置：买卖IC网 > PDF目录19280 > DS3882E+ (Maxim Integrated)IC CCFL CNTRLR DUAL 28TSSOP PDF资料下载
参数资料
| 型号： | DS3882E+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 16/31页 |
| 文件大小： | 0K |
| 描述： | IC CCFL CNTRLR DUAL 28TSSOP |
| 标准包装： | 50 |
| 类型： | CCFL 控制器 |
| 频率： | 40 ~ 100 kHz |
| 电流 - 电源： | 12mA |
| 电源电压： | 4.75 V ~ 5.25 V |
| 工作温度： | -40°C ~ 105°C |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 28-TSSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
Dual-Channel Automotive CCFL Controller
Figure 8 shows a flowchart of how the DS3882 controls
and monitors each lamp. The steps are as follows:
1) Supply Check—The lamps do not turn on unless the
DS3882 supply voltage is above 4.3V and the volt-
age at the supply voltage monitors, SVML and SVMH,
are respectively above 2.0V and below 2.0V.
2) Strike Lamp—When both the DS3882 and the DC
inverter supplies are at acceptable levels, the
DS3882 attempts to strike each enabled lamp. The
DS3882 slowly ramps up the MOSFET gate duty
cycle until the lamp strikes. The controller detects
that the lamp has struck by detecting current flow in
the lamp, detected by the LCMn pin. If during the
strike ramp, the maximum allowable voltage is
reached on the OVDn pin, the controller stops
increasing the MOSFET gate duty cycle to keep from
overstressing the system. The DS3882 goes into a
fault handling state (step 4) if the lamp has not struck
after the timeout period as defined by the LST0 and
LST1 control bits in the SSP1 register. If an overvolt-
age event is detected during the strike attempt, the
DS3882 disables the MOSFET gate drivers and go
into the fault handling state.
3) Run Lamp—Once the lamp is struck, the DS3882
adjusts the MOSFET gate duty cycle to optimize the
lamp current. The gate duty cycle is always con-
strained to keep the system from exceeding the
maximum allowable lamp voltage. The lamp current
sampling rate is user-selectable using the LSR0 and
LSR1 bits in CR2. If lamp current ever drops below the
lamp out reference point for the period as defined by
the LST0 and LST1 control bits in the SSP1 register,
then the lamp is considered extinguished. In this case,
the MOSFET gate drivers are disabled and the device
moves to the fault handling stage.
4) Fault Handling—During fault handling, the DS3882
performs an optional (user-selectable) automatic
retry to attempt to clear all faults except a lamp over-
current. The automatic retry makes 14 additional
attempts to rectify the fault before declaring the
channel in a fault state and permanently disabling
the channel. Between each of the 14 attempts, the
controller waits 1024 lamp cycles. In the case of a
lamp overcurrent, the DS3882 instantaneously
declares the channel to be in a fault state and per-
manently disables the channel. The DS3882 can be
configured to disable all channels if one or more
channels enter a fault state or it can be configured to
disable only the channel where the fault occurred.
Once a fault state is entered, the channel remains in
that state until one of the following occurs:
? V CC drops below the UVLO threshold.
? The SVML or SVMH thresholds are crossed.
? The PDN pin goes high.
? The PDNE software bit is written to a logic 1.
? The channel is disabled by the CH1D or CH2D
control bit.
16
____________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| V110A3V3T150BG2 | CONVERTER MOD DC/DC 3.3V 150W |
| FL7930BM | IC PFC CTLR FLYBACK/BOUND 8SOICN |
| RBM-1212D | CONV DC/DC 1W 12VIN +/-12VOUT |
| ACM31DTAH-S189 | CONN EDGECARD 62POS R/A .156 SLD |
| V110A3V3T150BG | CONVERTER MOD DC/DC 3.3V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS3882E/T&R | 制造商:Maxim Integrated Products 功能描述:CAR DUAL CCFL CTRL TSSOP-28 T&R - Tape and Reel |
| DS3882E+ | 功能描述:IC CCFL CNTRLR DUAL 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 照明，镇流器控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:CCFL 控制器 频率:40 ~ 80 kHz 电流 - 电源:5mA 电流 - 输出:- 电源电压:4.5 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) 其它名称:90-3991V+V01 |
| DS3882E+C | 功能描述:显示驱动器和控制器 DualCh Automotive CCFL Controller RoHS:否 制造商:Panasonic Electronic Components 工作电源电压:2.7 V to 5.5 V 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Reel |
| DS3882E+T&R | 制造商:Maxim Integrated Products 功能描述:IC CCFL CNTRLR DUAL 28TSSOP |
| DS3882E+T&R/C | 制造商:Maxim Integrated Products 功能描述:AUTOMOTIVE CCFL CNTRLR 28TSSOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC AUTO CCFL CTRLR 2CH 28-TSSOP |
发布紧急采购，3分钟左右您将得到回复。