- 您现在的位置：买卖IC网 > PDF目录97870 > DS80C323-MCD (MAXIM INTEGRATED PRODUCTS INC) 8-BIT, MROM, 18 MHz, MICROCONTROLLER, PDIP40 PDF资料下载
参数资料
| 型号： | DS80C323-MCD |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | Microcontroller |
| 英文描述： | 8-BIT, MROM, 18 MHz, MICROCONTROLLER, PDIP40 |
| 封装： | 0.600 INCH, PLASTIC, DIP-40 |
| 文件页数： | 15/38页 |
| 文件大小： | 694K |
| 代理商： | DS80C323-MCD |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
DS80C320/DS80C323 High-Speed/Low-Power Microcontrollers
22 of 38
NOTES FOR DS80C320 DC ELECTRICAL CHARACTERISTICS
All parameters apply to both commercial and industrial temperature operation unless otherwise noted. Specifications to -40°C
are guaranteed by design and are not production tested.
1. All voltages are referenced to ground.
2. Active current is measured with a 25MHz clock source driving XTAL1, VCC = RST = 5.5V, all other pins
disconnected.
3. Idle mode current is measured with a 25MHz clock source driving XTAL1, VCC = 5.5V, RST at ground, all
other pins disconnected.
4. Stop mode current measured with XTAL1 and RST grounded, VCC = 5.5V, all other pins disconnected.
5. When addressing external memory. This specification only applies to the first clock cycle following transition.
6. RST = VCC. This condition mimics operation of pins in I/O mode.
7. During a 0-to-1 transition, a one-shot drives the ports hard for two clock cycles. This measurement reflects port
in transition mode.
8. Ports 1 and 3 source transition current when being pulled down externally. It reaches its maximum at
approximately 2V.
9. 0.45<VIN<VCC. Not a high-impedance input. This port is a weak address holding latch because Port 0 is
dedicated as an address bus on the DS80C320. Peak current occurs near the input transition point of the latch,
approximately 2V.
10. Over the industrial temperature range, this specification has a maximum value of 200
A.
11. This is the current required from an external circuit to hold a logic low level on an I/O pin while the
corresponding port latch bit is set to 1. This is only the current required to hold the low level; transitions from 1
to 0 on an I/O pin will also have to overcome the transition current.
12. Device operating range is 4.5V to 5.5V; however, device is tested to 4.0V to ensure proper operation at
minimum VRST.
TYPICAL ICC vs. FREQUENCY
相关PDF资料 |
PDF描述 |
|---|---|
| DS80C320-QNL | 8-BIT, MROM, 33 MHz, MICROCONTROLLER, PQCC44 |
| DS80C320-MCL | 8-BIT, MROM, 33 MHz, MICROCONTROLLER, PDIP40 |
| DS80C323-ECD | 8-BIT, MROM, 18 MHz, MICROCONTROLLER, PQFP44 |
| DS80C320-QCL | 8-BIT, MROM, 33 MHz, MICROCONTROLLER, PQCC44 |
| DS80C320-MNL | 8-BIT, MROM, 33 MHz, MICROCONTROLLER, PDIP40 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS80C323-MCD+ | 功能描述:8位微控制器 -MCU High-Speed Low-Power RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| DS80C323MCG | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microprocessor |
| DS80C323-MCG | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:High-Speed Microcontroller User Guide |
| DS80C323-MCL | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:High-Speed Microcontroller User Guide |
| DS80C323-MCR | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:High-Speed Microcontroller User Guide |
发布紧急采购，3分钟左右您将得到回复。