- 您现在的位置：买卖IC网 > PDF目录97870 > DS80C323-MCD (MAXIM INTEGRATED PRODUCTS INC) 8-BIT, MROM, 18 MHz, MICROCONTROLLER, PDIP40 PDF资料下载
参数资料
| 型号： | DS80C323-MCD |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | Microcontroller |
| 英文描述： | 8-BIT, MROM, 18 MHz, MICROCONTROLLER, PDIP40 |
| 封装： | 0.600 INCH, PLASTIC, DIP-40 |
| 文件页数： | 37/38页 |
| 文件大小： | 694K |
| 代理商： | DS80C323-MCD |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页当前第37页第38页
DS80C320/DS80C323 High-Speed/Low-Power Microcontrollers
8 of 38
INSTRUCTION SET SUMMARY
All instructions in the DS80C320/DS80C323 perform the same functions as their 80C32 counterparts.
Their effect on bits, flags, and other status functions is identical. However, the timing of each instruction
is different. This applies both in absolute and relative number of clocks.
For absolute timing of real-time events, the timing of software loops will need to be calculated using the
Table 1. However, counter/timers default to run at the older 12 clocks per increment. Therefore, while
software runs at higher speed, timer-based events need no modification to operate as before. Timers can
be set to run at 4 clocks per increment cycle to take advantage of higher speed operation.
The relative time of two instructions might be different in the new architecture than it was previously. For
example, in the original architecture, the “MOVX A, @DPTR” instruction and the “MOV direct, direct”
instruction used two machine cycles or 24 oscillator cycles. Therefore, they required the same amount of
time. In the DS80C320/DS80C323, the MOVX instruction can be done in two machine cycles or eight
oscillator cycles, but the “MOV direct, direct” uses three machine cycles or 12 oscillator cycles. While
both are faster than their original counterparts, they now have different execution times from each other.
This is because in most cases, the DS80C320/DS80C323 use one cycle for each byte. The user concerned
with precise program timing should examine the timing of each instruction for familiarity with the
changes. Note that a machine cycle now requires just four clocks, and provides one ALE pulse per cycle.
Many instructions require only one cycle, but some require five. In the original architecture, all were one
or two cycles except for MUL and DIV.
相关PDF资料 |
PDF描述 |
|---|---|
| DS80C320-QNL | 8-BIT, MROM, 33 MHz, MICROCONTROLLER, PQCC44 |
| DS80C320-MCL | 8-BIT, MROM, 33 MHz, MICROCONTROLLER, PDIP40 |
| DS80C323-ECD | 8-BIT, MROM, 18 MHz, MICROCONTROLLER, PQFP44 |
| DS80C320-QCL | 8-BIT, MROM, 33 MHz, MICROCONTROLLER, PQCC44 |
| DS80C320-MNL | 8-BIT, MROM, 33 MHz, MICROCONTROLLER, PDIP40 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS80C323-MCD+ | 功能描述:8位微控制器 -MCU High-Speed Low-Power RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| DS80C323MCG | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microprocessor |
| DS80C323-MCG | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:High-Speed Microcontroller User Guide |
| DS80C323-MCL | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:High-Speed Microcontroller User Guide |
| DS80C323-MCR | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:High-Speed Microcontroller User Guide |
发布紧急采购，3分钟左右您将得到回复。