- 您现在的位置：买卖IC网 > PDF目录97870 > DS80C323-MCD (MAXIM INTEGRATED PRODUCTS INC) 8-BIT, MROM, 18 MHz, MICROCONTROLLER, PDIP40 PDF资料下载
参数资料
| 型号： | DS80C323-MCD |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | Microcontroller |
| 英文描述： | 8-BIT, MROM, 18 MHz, MICROCONTROLLER, PDIP40 |
| 封装： | 0.600 INCH, PLASTIC, DIP-40 |
| 文件页数： | 33/38页 |
| 文件大小： | 694K |
| 代理商： | DS80C323-MCD |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页当前第33页第34页第35页第36页第37页第38页
DS80C320/DS80C323 High-Speed/Low-Power Microcontrollers
4 of 38
PIN DESCRIPTION (continued)
PIN
DIP
PLCC
TQFP
NAME
FUNCTION
30
33
27
ALE
Address Latch-Enable Output. This pin functions as a clock to latch
the external address LSB from the multiplexed address/data bus. This
signal is commonly connected to the latch enable of an external 373
family transparent latch. ALE has a pulse width of 1.5 XTAL1 cycles
and a period of four XTAL1 cycles. ALE is forced high when the
device is in a reset condition.
39
43
37
AD0
38
42
36
AD1
37
41
35
AD2
36
40
34
AD3
35
39
33
AD4
34
38
32
AD5
33
37
31
AD6
32
36
30
AD7
Port 0, Input/Output. Port 0 is the multiplexed address/data bus.
During the time when ALE is high, the LSB of a memory address is
presented. When ALE falls, the port transitions to a bidirectional data
bus. This bus is used to read external ROM and read/write external
RAM memory or peripherals. The Port 0 has no true port latch and
cannot be written directly by software. The reset condition of Port 0 is
high. No pullup resistors are needed.
Port 1, I/O. Port 1 functions as both an 8-bit, bidirectional I/O port and
an alternate functional interface for Timer 2 I/O, new External
Interrupts, and new Serial Port 1. The reset condition of Port 1 is with
all bits at logic 1. In this state, a weak pullup holds the port high. This
condition also serves as an input mode, since any external circuit that
writes to the port will overcome the weak pullup. When software writes
a 0 to any port pin, the device will activate a strong pulldown that
remains on until either a 1 is written or a reset occurs. Writing a 1 after
the port has been at 0 will cause a strong transition driver to turn on,
followed by a weaker sustaining pullup. Once the momentary strong
driver turns off, the port once again becomes the output high (and
input) state. The alternate modes of Port 1 are outlined as follows:
PIN
DIP
PLCC
TQFP
PORT
ALTERNATE
FUNCTION
1
2
40
P1.0
T2
External I/O for
Timer/Counter 2
2
3
41
P1.1
T2EX
Timer/Counter 2
Capture/Reload Trigger
3
4
42
P1.2
RXD1
Serial Port 1 Input
4
5
43
P1.3
TXD1
Serial Port 1 Output
5
6
44
P1.4
INT2
External Interrupt 2
(Positive-Edge Detect)
6
7
1
P1.5
INT3
External Interrupt 3
(Negative-Edge Detect)
7
8
2
P1.6
INT4
External Interrupt 4
(Positive-Edge Detect)
1–8
2–9
40–44,
1–3
P1.0–P1.7
8
9
3
P1.7
INT5
External Interrupt 5
(Negative-Edge Detect)
相关PDF资料 |
PDF描述 |
|---|---|
| DS80C320-QNL | 8-BIT, MROM, 33 MHz, MICROCONTROLLER, PQCC44 |
| DS80C320-MCL | 8-BIT, MROM, 33 MHz, MICROCONTROLLER, PDIP40 |
| DS80C323-ECD | 8-BIT, MROM, 18 MHz, MICROCONTROLLER, PQFP44 |
| DS80C320-QCL | 8-BIT, MROM, 33 MHz, MICROCONTROLLER, PQCC44 |
| DS80C320-MNL | 8-BIT, MROM, 33 MHz, MICROCONTROLLER, PDIP40 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS80C323-MCD+ | 功能描述:8位微控制器 -MCU High-Speed Low-Power RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| DS80C323MCG | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microprocessor |
| DS80C323-MCG | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:High-Speed Microcontroller User Guide |
| DS80C323-MCL | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:High-Speed Microcontroller User Guide |
| DS80C323-MCR | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:High-Speed Microcontroller User Guide |
发布紧急采购，3分钟左右您将得到回复。