- 您现在的位置：买卖IC网 > PDF目录10918 > DS89C430-QNG+ (Maxim Integrated Products)IC MCU FLASH 16KB 25MHZ 44-PLCC PDF资料下载
参数资料
| 型号： | DS89C430-QNG+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 36/46页 |
| 文件大小： | 0K |
| 描述： | IC MCU FLASH 16KB 25MHZ 44-PLCC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 26 |
| 系列： | 89C |
| 核心处理器： | 8051 |
| 芯体尺寸： | 8-位 |
| 速度： | 25MHz |
| 连通性： | EBI/EMI，SIO，UART/USART |
| 外围设备： | 电源故障复位，WDT |
| 输入/输出数： | 32 |
| 程序存储器容量： | 16KB（16K x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 1K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 4.5 V ~ 5.5 V |
| 振荡器型： | 外部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 44-LCC（J 形引线） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页当前第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
DS89C430/DS89C450 Ultra-High-Speed Flash Microcontrollers
41 of 46
External/Hardware Reset
A hardware reset can be initiated by asserting the RST pin high for at least three external clock cycles while the
external clock is running. The reset is asserted immediately.
When the RST pin is taken to a logic low, the microcontroller exits the reset state within a delay that depends on
the state of the flash memory at the time the reset was asserted. If a flash write or erase operation was in progress,
the reset state is a 4ms maximum. If no flash write or erase operations were in progress, there is a delay of 90
external clock cycles. Operation resumes at address 0000h. If taking RST to a logic low causes the device to exit
stop mode, an additional delay of 65,536 clock cycles is experienced before operation begins.
Reset Output
If a reset is caused by a power-fail reset, a watchdog timer reset, or an internal system reset, a logic high output-
reset pulse is also generated at the bidirectional RST pin. This reset pulse is asserted as long as an internal reset
is asserted. Although the microcontroller generates its own power-on delay for crystal warmup, legacy designs may
employ an external RC circuit. Large values of “C” may load the pin enough that the RST output may not achieve a
logic high, but the state of the external RST pin does not affect the internal reset condition.
Oscillator-Fail Detect and Reset
The DS89C430 incorporates an oscillator-fail-detect circuit that, when enabled, causes a reset if the crystal
oscillator frequency falls below 20kHz and holds the chip in reset with the ring oscillator operating. Setting the
OFDE (PCON.4) bit to logic 1 enables the circuit. The OFDE bit is only cleared from logic 1 to logic 0 by a power-
fail reset or by software. A reset caused by an oscillator failure also sets the OFDF (PCON.5) to logic 1. This flag is
cleared by software or power-on reset. This circuit does not force a reset when the oscillator is stopped by the
software-enabled stop mode.
Power-Management Mode
The power-management mode offers a software-controllable power-saving scheme by providing a reduced
instruction cycle speed, which allows the microcontroller to continue operating while using an internally divided
version of the clock source to save power. Power-management mode is invoked by software setting the clock-
divide control bits CD1 and CD0 (PMR.7–6) bits to 11b, which sets an operating rate of 1024 oscillator cycles for
one machine cycle. On all forms of reset, the clock-divide control bits default to 10b, which selects one oscillator
cycle per machine cycle.
Since the clock speed choice affects all functional logic, including timers, several hardware switchback features
allow the clock speed to automatically return to the divide-by-1 mode from a reduced cycle rate. Setting the SWB
(PMR.5) bit to 1 in software enables this switchback function.
When CD1 and CD0 are programmed to the divide-by-1024 mode and the SWB bit is also enabled, the system
forces the clock-divide control bits to automatically reset to the divide-by-1 mode whenever the system detects an
externally enabled (and allowed by nesting priorities) interrupt. The switchback occurs whenever one of the two
following conditions occurs. The first switchback condition is initiated by the detection of a low on either INT0, INT1,
INT3
, or INT5 or a high on INT2 or INT4 when the respective pin has been programmed and allowed (by nesting
priorities) to issue an interrupt. The second switchback condition occurs when either serial port is enabled to
receive data and is found to have an active-low transition on the respective receive-input pin. Serial port transmit
activity also forces a switchback if the SWB is set. Note that the serial port activity, as related to the switchback, is
independent of the serial port interrupt relationship. Any attempt to change the clock divider to the divide-by-1024
mode while the serial port is either transmitting or receiving has no effect, leaving the clock control in the divide-by-
1 mode. Note also that the switchback interrupt relationship requires that the respective external interrupt source is
allowed to actually generate an interrupt, as defined by the priority of the interrupt and the state of the nested
interrupts, before the switchback can actually occur. An interrupt by the serial port is not required, nor is the setting
of serial port enable. Disabling external interrupts and serial port receive/transmission mode disables the automatic
switchback mode. Clearing the SWB bit also disables the switchback, and all interrupt and serial port controls of
the clock divider are disabled. All other clock modes ignore the switchback relationship and are unaffected by
interrupts and serial port activity.
The basic divide-by-12 mode for the timers (TxMH, TxM = 00b) as well as the divide by 32 and 64 for mode 2 on
the serial ports has been maintained when running the processor with the oscillator divide ratio of 0.25, 0.5, and 1.
相关PDF资料 |
PDF描述 |
|---|---|
| DS89C430-QNG | IC MCU FLASH 16KB 25MHZ 44-PLCC |
| SAB-C161O-LM 3V HA | IC MICROCONTROLLER 16BIT MQFP80 |
| SAB-C161K-LM HA | IC MICROCONTROLLER 16BIT MQFP80 |
| JBXFD2G05MSSDSR | CONN PLUG 5POS STR CABLE SOLDER |
| VI-23V-IX-F1 | CONVERTER MOD DC/DC 5.8V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS89C430-QNG+ | 功能描述:8位微控制器 -MCU Ultra-High-Speed Flash MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| DS89C430QNL | 制造商:Maxim Integrated Products 功能描述:Bulk |
| DS89C430-QNL | 功能描述:8位微控制器 -MCU Ultra-High-Speed Flash MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| DS89C430-QNL+ | 功能描述:8位微控制器 -MCU Ultra-High-Speed Flash MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| DS89C430-QNL+ | 制造商:Maxim Integrated Products 功能描述:IC 8BIT MCU 8051 33MHZ LCC-44 |
发布紧急采购，3分钟左右您将得到回复。