参数资料
型号: DSPIC33FJ32GP202-E/SS
厂商: Microchip Technology
文件页数: 30/176页
文件大小: 0K
描述: IC DSC 16BIT 32KB FLASH 28SSOP
标准包装: 47
系列: dsPIC™ 33F
核心处理器: dsPIC
芯体尺寸: 16-位
速度: 40 MIP
连通性: I²C,IrDA,LIN,SPI,UART/USART
外围设备: 欠压检测/复位,POR,PWM,WDT
输入/输出数: 21
程序存储器容量: 32KB(32K x 8)
程序存储器类型: 闪存
RAM 容量: 2K x 8
电压 - 电源 (Vcc/Vdd): 3 V ~ 3.6 V
数据转换器: A/D 10x10b/12b
振荡器型: 内部
工作温度: -40°C ~ 125°C
封装/外壳: 28-SSOP(0.209",5.30mm 宽)
包装: 管件
123
AT89C5131
4136C–USB–04/05
Bulk/Interrupt IN Transactions
in Standard Mode
Figure 61. Bulk/Interrupt IN Transactions in Standard Mode
An endpoint will be first enabled and configured before being able to send Bulk or Inter-
rupt packets.
The firmware will fill the FIFO with the data to be sent and set the TXRDY bit in the UEP-
STAX register to allow the USB controller to send the data stored in FIFO at the next IN
request concerning this endpoint. To send a Zero Length Packet, the firmware will set
the TXRDY bit without writing any data into the endpoint FIFO.
Until the TXRDY bit has been set by the firmware, the USB controller will answer a NAK
handshake for each IN requests.
To cancel the sending of this packet, the firmware has to reset the TXRDY bit. The
packet stored in the endpoint FIFO is then cleared and a new packet can be written and
sent.
When the IN packet has been sent and acknowledged by the Host, the TXCMPL bit in
the UEPSTAX register is set by the USB controller. This triggers a USB interrupt if
enabled. The firmware will clear the TXCMPL bit before filling the endpoint FIFO with
new data.
The firmware will never write more bytes than supported by the endpoint FIFO.
All USB retry mechanisms are automatically managed by the USB controller.
IN
DATA0 (n Bytes)
ACK
HOST
UFI
C51
Endpoint FIFO Write Byte 1
IN
NAK
TXCMPL
Endpoint FIFO Write Byte 2
Endpoint FIFO Write Byte n
Set TXRDY
Clear TXCMPL
Endpoint FIFO Write Byte 1
相关PDF资料
PDF描述
VE-B6V-IX-S CONVERTER MOD DC/DC 5.8V 75W
PIC18F65K90-E/PT IC MCU 8BIT 32KB FLASH 64TQFP
VE-B6T-IX-S CONVERTER MOD DC/DC 6.5V 75W
PIC18F47J13T-I/PT IC MCU 8BIT 128KB FLASH 44 TQFP
PIC24FJ64GA102T-I/ML IC MCU 16BIT 64KB FLASH 28QFN
相关代理商/技术参数
参数描述
dsPIC33FJ32GP202-I/MM 功能描述:数字信号处理器和控制器 - DSP, DSC 16B DSC 28LD 32KB Flash40 RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
dsPIC33FJ32GP202-I/SO 功能描述:数字信号处理器和控制器 - DSP, DSC 16B DSC 28LD 32KB Flash40 RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
dsPIC33FJ32GP202-I/SP 功能描述:数字信号处理器和控制器 - DSP, DSC 16B DSC 28LD 32KB Flash40 RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
dsPIC33FJ32GP202-I/SS 功能描述:数字信号处理器和控制器 - DSP, DSC 16 bit DSC 40MIPS 32KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
DSPIC33FJ32GP202T-E/MM 制造商:Microchip Technology Inc 功能描述: