收藏本站
参数资料
型号： DSPIC33FJ32GP202-I/SS
厂商： Microchip Technology
文件页数： 129/176页
文件大小： 0K
描述： IC DSPIC MCU/DSP 32K 28SSOP
标准包装： 47
系列： dsPIC™ 33F
核心处理器： dsPIC
芯体尺寸： 16-位
速度： 40 MIP
连通性： I²C，IrDA，LIN，SPI，UART/USART
外围设备： 欠压检测/复位，POR，PWM，WDT
输入/输出数： 21
程序存储器容量： 32KB（32K x 8）
程序存储器类型： 闪存
RAM 容量： 2K x 8
电压 - 电源 (Vcc/Vdd)： 3 V ~ 3.6 V
数据转换器： A/D 10x10b/12b
振荡器型： 内部
工作温度： -40°C ~ 85°C
封装/外壳： 28-SSOP（0.209"，5.30mm 宽）
包装： 管件
dsPIC33FJ32GP202/204 and dsPIC33FJ16GP304
DS70290J-page 56
2007-2011 Microchip Technology Inc.
5.2
RTSP Operation
The
dsPIC33FJ32GP202/204
and
dsPIC33FJ16GP304 Flash program memory array is
organized into rows of 64 instructions or 192 bytes.
RTSP allows the user application to erase a page of
memory, which consists of eight rows (512 instructions)
at a time, and to program one row or one word at a
time. The 8-row erase pages and single row write rows
are edge-aligned from the beginning of program
memory, on boundaries of 1536 bytes and 192 bytes,
respectively.
The program memory implements holding buffers that
can contain 64 instructions of programming data. Prior
to the actual programming operation, the write data
must be loaded into the buffers sequentially. The
instruction words loaded must always be from a group
of 64 boundary.
The basic sequence for RTSP programming is to set up
a Table Pointer, then do a series of TBLWT instructions
to load the buffers. Programming is performed by
setting the control bits in the NVMCON register. A total
of 64 TBLWTL and TBLWTH instructions are required
to load the instructions.
All of the table write operations are single-word writes
(two instruction cycles) because only the buffers are
written. A programming cycle is required for
programming each row.
5.3
Programming Operations
A complete programming sequence is necessary for
programming or erasing the internal Flash in RTSP
mode.
The
processor stalls (waits)
until
the
programming operation is finished.
The programming time depends on the FRC accuracy
(see Table 22-18) and the value of the FRC Oscillator
Tuning register (see Register 8-4). Use the following
formula to calculate the minimum and maximum values
for the Row Write Time, Page Erase Time, and Word
Write Cycle Time parameters (see Table 22-12).
EQUATION 5-1:
PROGRAMMING TIME
For example, if the device is operating at +125
° C, the
FRC accuracy will be ±5%. If the TUN<5:0> bits (see
Register 8-4) are set to ‘b111111, the minimum row
write time is equal to Equation 5-2.
EQUATION 5-2:
MINIMUM ROW WRITE
TIME
The maximum row write time is equal to Equation 5-3.
EQUATION 5-3:
MAXIMUM ROW WRITE
TIME
Setting the WR bit (NVMCON<15>) starts the
operation, and the WR bit is automatically cleared
when the operation is finished.
5.4
Flash Memory Resources
Many useful resources are provided on the main prod-
uct page of the Microchip web site for the devices listed
in this data sheet. This product page, which can be
accessed using this link, contains the latest updates
and additional information.
5.4.1
KEY RESOURCES
Section 5. “Flash Programming” (DS70191)
Code Samples
Application Notes
Software Libraries
Webinars
All related dsPIC33F/PIC24H Family Reference
Manuals Sections
Development Tools
5.5
Control Registers
The two SFRs that are used to read and write the
program Flash memory are:
NVMCON: Flash Memory Control Register
NVMKEY: Nonvolatile Memory Key Register
The NVMCON register (Register 5-1) controls which
blocks are to be erased, which memory type is to be
programmed and the start of the programming cycle.
NVMKEY (Register 5-2) is a write-only register that is
used for write protection. To start a programming or
erase
sequence,
the
user
application
must
consecutively write 0x55 and 0xAA to the NVMKEY
register.
Refer
to
Section 5.3
“Programming
Operations” for further details.
T
7.37 MHz
FRC Accuracy
()%
FRC Tuning
()%
×
----------------------------------------------------------------------------------------------------------------------------
TRW
11064 Cycles
7.37 MHz
10.05
+
()
1 0.00375
–
()
×
------------------------------------------------------------------------------------------------ 1.435ms
=
Note:
In the event you are not able to access
the product page using the link above,
enter
this
URL
in
your
browser:
http://www.microchip.com/wwwproducts/
Devices.aspx?dDocName=en530331
TRW
11064 Cycles
7.37 MHz
10.05
–
()
1 0.00375
–
()
×
------------------------------------------------------------------------------------------------ 1.586ms
=
相关PDF资料
PDF描述
UPL2000-D2 BNC PLUG CRIMP STR BELDEN 1505A
VE-B4D-IX-F1 CONVERTER MOD DC/DC 85V 75W
PIC24FV32KA304-I/ML MCU 32KB FLASH 2KB RAM 44-QFN
MS27497T24B29P CONN RCPT 29POS WALL MNT W/PINS
VE-B4D-IW-F4 CONVERTER MOD DC/DC 85V 100W
相关代理商/技术参数
参数描述
DSPIC33FJ32GP202T-E/MM 制造商:Microchip Technology Inc 功能描述:
dsPIC33FJ32GP202T-I/MM 功能描述:数字信号处理器和控制器 - DSP, DSC 16B DSC 28LD32KB 40 MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
dsPIC33FJ32GP202T-I/SO 功能描述:数字信号处理器和控制器 - DSP, DSC 16B DSC 28LD32KB 40 MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
dsPIC33FJ32GP202T-I/SS 功能描述:数字信号处理器和控制器 - DSP, DSC 16 bit DSC 40MIPS 32KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
dsPIC33FJ32GP204-E/ML 功能描述:数字信号处理器和控制器 - DSP, DSC 16B DSC 44LD32KB 40 MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*