- 您现在的位置：买卖IC网 > Datasheet目录323 > DV164039 (Microchip Technology)KIT DEV PIC24FJ256DA210 Datasheet资料下载
参数资料
| 型号： | DV164039 |
| 厂商： | Microchip Technology |
| 文件页数： | 37/64页 |
| 文件大小： | 0K |
| 描述： | KIT DEV PIC24FJ256DA210 |
| 产品培训模块： | Intro to PIC24FJDA Family |
| 视频文件： | PIC24FJ256DA210 Development Board Overview |
| 标准包装： | 1 |
| 系列： | dsPIC™ |
| 类型： | MCU |
| 适用于相关产品： | PIC24FJ256DA210 |
| 所含物品： | 开发板，显示板，3 个裸板，MPLAB ICD-3，线缆，电源 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页当前第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
Development Board Hardware
4.4.1.2
CTMU TOUCH SENSE INPUTS
The development board is equipped with five touch sensor inputs. These are multi-
plexed between three CTMU (Charge Time Measurement Unit) analog channels, as
shown in Table 4-4. The areas within the white border of each pad is the touch-sensitive
areas. Note that all three CTMU inputs must be enabled to use the entire pad.
TABLE 4-4:
CTMU TOUCH PAD COMBINATIONS
Touch Pad
PAD1 (RG8)
PAD2 (RE9)
PAD3 (RB5)
LEFT
RIGHT
UP
DOWN
X
X
X
X
X
X
SEL
To enable the CTMU Touch Pads:
1. To enable PAD1 (Figure 4-3, callout 1):
a) Set jumper JP13 to position PAD1–RG8
b) If installed, remove resistors R26 and R27
c) Populate resistor R25 with a 0 ? resistor (default)
2. To enable PAD2 (Figure 4-3, callout 2):
a) Set jumper JP14 to position PAD2–RE9
b) If installed, remove resistor R32
c) Populate resistor R31 with a 0 ? resistor (default)
3. To enable PAD3 (Figure 4-3, callout 3):
a) Set jumper JP15 to position PAD3–RB5
b) If installed, remove resistor R45
c) Populate resistor R41 with a 0 ? resistor (default)
X
X
Note:
4.4.1.3
CTMU signals are connected to PIC24FJ256DA210 analog pins. Make
sure that the pins are set to analog pins using their corresponding ANSx
control bits. Refer to the “ PIC24FJ256DA210 Family Data Sheet
(DS39969)” for details.
ANALOG INPUT (POTENTIOMETER)
Pin RB5 can also be configured to read potentiometer R3. This selection is enabled by
setting JP15 to position RB5–POT. No other changes are required.
4.4.1.4
LED OUTPUTS
There are four user-defined LEDs on the development board.
LEDs D1, D2 and D3 (red) are multiplexed with the CTMU pads. They are individually
enabled when their corresponding CTMU pads are enabled, as described in
LED D4 (red) is multiplexed with address line 17 of the parallel RAM and Flash mem-
ories. To use this LED, jumper JP11 must be set to position 1-2. Refer to
? 2010 Microchip Technology Inc.
DS51911A-page 37
相关PDF资料 |
PDF描述 |
|---|---|
| DV164101 | KIT DEV PICKIT1 FLASH 8/14PIN |
| DV164120 | KIT STARTER PICKIT 2 |
| DV164121 | KIT PICKIT 2 DEBUG EXPRESS |
| DV164122 | ANALYZER SRL PICKIT W/DEMO BOARD |
| DV164131 | KIT STARTER PICKIT 3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DV164101 | 功能描述:开发板和工具包 - PIC / DSPIC PICkit 1 8/14P Flash RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压: |
| DV164101 | 制造商:Microchip Technology Inc 功能描述:TOOLS: FLASH MICROCONTROLLER ( |
| DV164102 | 功能描述:开发板和工具包 - 无线 rfPICkit RoHS:否 制造商:Arduino 产品:Evaluation Boards 工具用于评估:AT32UC3L 核心:AVR32 频率: 接口类型:USB 工作电源电压:5 V |
| DV164120 | 功能描述:电路内置调试器 PICkit 2 8/14/20P Flash RoHS:否 制造商:Microchip Technology 产品:In-Circuit Debugger Kits 工具用于评估:PIC MCUs, dsPIC DSCs 用于:07-00024, AC164113 核心:dsPIC, PIC 接口类型:USB 工作电源电压:3 V to 5 V |
| DV164121 | 功能描述:电路内置调试器 PICkit 2 Debug Express RoHS:否 制造商:Microchip Technology 产品:In-Circuit Debugger Kits 工具用于评估:PIC MCUs, dsPIC DSCs 用于:07-00024, AC164113 核心:dsPIC, PIC 接口类型:USB 工作电源电压:3 V to 5 V |
发布紧急采购，3分钟左右您将得到回复。