- 您现在的位置：买卖IC网 > PDF目录15544 > DV164136 (Microchip Technology)DEVELOPMENT KIT FOR PIC18 PDF资料下载
参数资料
| 型号： | DV164136 |
| 厂商： | Microchip Technology |
| 文件页数： | 4/107页 |
| 文件大小： | 0K |
| 描述： | DEVELOPMENT KIT FOR PIC18 |
| 产品培训模块： | PIC18 J Series MCU Overview |
| 标准包装： | 1 |
| 系列： | PIC® |
| 类型： | MCU |
| 适用于相关产品： | PIC18F8722，PIC18F87J11 |
| 所含物品： | 板，线缆，CD，PICkit? 3 个编程器，电源 |
| 产品目录页面： | 659 (CN2011-ZH PDF) |
| 相关产品： | PIC18F87J11-I/PT-ND - IC PIC MCU FLASH 64KX16 80TQFP PIC18F87J11T-I/PTTR-ND - IC PIC MCU FLASH 64KX16 80TQFP PIC18F8722T-E/PT-ND - IC PIC MCU FLASH 64KX16 80TQFP PIC18F8722-E/PT-ND - IC PIC MCU FLASH 64KX16 80TQFP PIC18F8722T-I/PT-ND - IC PIC MCU FLASH 64KX16 80TQFP PIC18F8722-I/PT-ND - IC PIC MCU FLASH 64KX16 80TQFP |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页
2007-2012 Microchip Technology Inc.
DS39778E-page 101
PIC18F87J11 FAMILY
7.5
Writing to Flash Program Memory
The programming block is 32 words or 64 bytes.
Programming one word or two bytes at a time is also
supported.
Table writes are used internally to load the holding
registers needed to program the Flash memory. There
are 64 holding registers used by the table writes for
programming.
Since the Table Latch (TABLAT) is only a single byte, the
TBLWT
instruction may need to be executed 64 times for
each programming operation (if WPROG = 0). All of the
table write operations will essentially be short writes
because only the holding registers are written. At the
end of updating the 64 holding registers, the EECON1
register must be written to in order to start the
programming operation with a long write.
The long write is necessary for programming the inter-
nal Flash. Instruction execution is halted while in a long
write cycle. The long write will be terminated by the
internal programming timer.
The on-chip timer controls the write time. The
write/erase voltages are generated by an on-chip
charge pump, rated to operate over the voltage range
of the device.
FIGURE 7-5:
TABLE WRITES TO FLASH PROGRAM MEMORY
7.5.1
FLASH PROGRAM MEMORY WRITE
SEQUENCE
The sequence of events for programming an internal
program memory location should be:
1.
Read 1024 bytes into RAM.
2.
Update data values in RAM as necessary.
3.
Load Table Pointer register with address being
erased.
4.
Execute the row erase procedure.
5.
Load Table Pointer register with address of first
byte being written, minus 1.
6.
Write the 64 bytes into the holding registers with
auto-increment.
7.
Set the WREN bit (EECON1<2>) to enable byte
writes.
8.
Disable interrupts.
9.
Write H'55' to EECON2.
10. Write H'AA' to EECON2.
11. Set the WR bit. This will begin the write cycle.
12. The CPU will stall for duration of the write for TIW
(Parameter D133A).
13. Re-enable interrupts.
14. Repeat Steps 6 through 13 until all 1024 bytes
are written to program memory.
15. Verify the memory (table read).
An example of the required code is shown in
Example 7-3 on the following page.
Note 1:
Unlike previous PIC18 Flash devices,
members of the PIC18F87J11 family do
not reset the holding registers after a
write occurs. The holding registers must
be cleared or overwritten before a
programming sequence.
2:
To maintain the endurance of the pro-
gram memory cells, each Flash byte
should not be programmed more than
one time between erase operations.
Before attempting to modify the contents
of the target cell a second time, a row
erase of the target row or a bulk erase of
the entire memory, must be performed.
TBLPTR = xxxx3F
TBLPTR = xxxxx1
TBLPTR = xxxxx0
TBLPTR = xxxxx2
Program Memory
Holding Register
8
TABLAT
Write Register
Note:
Before setting the WR bit, the Table
Pointer address needs to be within the
intended address range of the 64 bytes in
the holding register.
相关PDF资料 |
PDF描述 |
|---|---|
| GBM25DCWT | CONN EDGECARD 50POS DIP .156 SLD |
| GCM24DCTN | CONN EDGECARD 48POS DIP .156 SLD |
| 1435863-2 | PATCHCORD CAT6 YLW/YLW BOOT 2' |
| 1435862-2 | PATCHCORD CAT6 RED/RED BOOT 2' |
| V48C5T50BF3 | CONVERTER MOD DC/DC 5V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DV164139 | 功能描述:开发板和工具包 - PIC / DSPIC Lo PIn Count USB Dev Kit (w/PICkit 3) RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压: |
| DV17K3225T | 制造商:SEI Stackpole Electronics Inc 功能描述:- Tape and Reel 制造商:SEI Stackpole Electronics Inc 功能描述:Var MOV 17VAC/22VDC 100A 27V 3225 SMD T/R |
| DV17K4032T | 制造商:SEI Stackpole Electronics Inc 功能描述:VAR 17VAC 22VDC 250A 27V 4032 SMD - Tape and Reel 制造商:SEI Stackpole Electronics Inc 功能描述:Var MOV 17VAC/22VDC 250A 27V 4032 SMD T/R |
| DV18-145MB-3K | 功能描述:端子 PIN -DSC 22-18 145X032 VYL RED RoHS:否 制造商:AVX 产品:Junction Box - Wire to Wire 系列:9826 线规:26-18 接线柱/接头大小: 绝缘: 颜色:Red 型式:Female 触点电镀:Tin over Nickel 触点材料:Beryllium Copper, Phosphor Bronze 端接类型:Crimp |
| DV18-145M-C | 功能描述:端子 MALE BLADE ADAPT RoHS:否 制造商:AVX 产品:Junction Box - Wire to Wire 系列:9826 线规:26-18 接线柱/接头大小: 绝缘: 颜色:Red 型式:Female 触点电镀:Tin over Nickel 触点材料:Beryllium Copper, Phosphor Bronze 端接类型:Crimp |
发布紧急采购，3分钟左右您将得到回复。