- 您现在的位置：买卖IC网 > PDF目录14583 > EL7562CUZ (Intersil)IC REG BUCK SYNC ADJ 2A 16QSOP PDF资料下载
参数资料
| 型号： | EL7562CUZ |
| 厂商： | Intersil |
| 文件页数： | 8/9页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 2A 16QSOP |
| 标准包装： | 97 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1 V ~ 3.8 V |
| 输入电压： | 3.5 V ~ 5 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 1MHz |
| 电流 - 输出： | 2A |
| 同步整流器： | 是 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 供应商设备封装： | 16-QSOP |
| 产品目录页面： | 1242 (CN2011-ZH PDF) |
V OUT = 0.985 × ? 1 + ------ 2 - ?
The heart of the controller is an input direct summing
comparator which sum voltage feedback, current feedback,
slope compensation ramp and power tracking signals
together. Slope compensation is required to prevent system
instability that occurs in current-mode topologies operating
at duty-cycles greater than 50% and is also used to define
the open-loop gain of the overall system. The slope
compensation is fixed internally and optimized for 500mA
inductor ripple current. The power tracking will not contribute
any input to the comparator steady-state operation. Current
feedback is measured by the patented sensing scheme that
senses the inductor current flowing through the high-side
switch whenever it is conducting. At the beginning of each
oscillator period the high-side NMOS switch is turned on.
The comparator inputs are gated off for a minimum period of
time of about 150ns (LEB) after the high-side switch is
turned on to allow the system to settle. The Leading Edge
Blanking (LEB) period prevents the detection of erroneous
voltages at the comparator inputs due to switching noise. If
the inductor current exceeds the maximum current limit
(I LMAX ) a secondary over-current comparator will terminate
the high-side switch on time. If I LMAX has not been reached,
the feedback voltage FB derived from the regulator output
voltage V OUT is then compared to the internal feedback
reference voltage. The resultant error voltage is summed
with the current feedback and slope compensation ramp.
The high-side switch remains on until all four comparator
inputs have summed to zero, at which time the high-side
switch is turned off and the low-side switch is turned on.
However, the maximum on-duty ratio of the high-side switch
is limited to 95%. In order to eliminate cross-conduction of
the high-side and low-side switches a 15ns break-before-
make delay is incorporated in the switch drive circuitry. The
output enable (EN) input allows the regulator output to be
disabled by an external logic control signal.
Output Voltage Setting
In general:
? R ?
? R 1 ?
For V IN = 5V
NMOS Power FETs and Drive Circuitry
The EL7562 integrates low on-resistance (60m Ω ) NMOS
FETs to achieve high efficiency at 2A. In order to use an
NMOS switch for the high-side drive it is necessary to drive
the gate voltage above the source voltage (LX). This is
accomplished by bootstrapping the V HI pin above the LX
voltage with an external capacitor C VHI and internal switch
and diode. When the low-side switch is turned on and the LX
voltage is close to GND potential, capacitor C VHI is charged
through internal switch to V DRV , typically 5V. At the
beginning of the next cycle the high-side switch turns on and
the LX pins begin to rise from GND to V IN potential. As the
LX pin rises the positive plate of capacitor C VHI follows and
eventually reaches a value of V DRV +V IN , typically 10V, for
V DRV =V IN =5V. This voltage is then level shifted and used to
drive the gate of the high-side FET, via the V HI pin. A value
of 0.1μF for C VHI is recommended.
Reference
A 1.5% temperature compensated bandgap reference is
integrated in the EL7562. The external V REF capacitor acts
as the dominant pole of the amplifier and can be increased
in size to maximize transient noise rejection. A value of
0.1μF is recommended.
Oscillator
The system clock is generated by an internal relaxation
oscillator with a maximum duty-cycle of approximately 95%.
Operating frequency can be adjusted through the C OSC pin
or can be driven by an external source. If the oscillator is
driven by an external source care must be taken in selecting
the ramp amplitude. Since C SLOPE value is derived from the
C OSC ramp, changes to C OSC ramp will change the
C SLOPE compensation ramp which determine the open-loop
gain of the system.
When external synchronization is required, always choose
C OSC such that the free-running frequency is at least 20%
lower than that of sync source to accommodate component
and temperature variations. Figure 1 shows a typical
connection.
1
16
100p
BAT54
V OUT = 0.975 × ? 1 + ------ 2 - ?
? R ?
? R 1 ?
External
Oscillato
2
3
15
14
FOR V IN = 3.3V
However, due to the relatively low open loop gain of the
system, gain errors will occur as the output voltage and loop-
gain is changed. This is shown in the performance curves. A
100nA pull-up current from FB to V DD forces V OUT to GND
in the event that FB is floating.
6
7
8
EL7562
11
10
9
FIGURE 1. OSCILLATOR SYNCHRONIZATION
8
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6468US35D7+T | IC MPU/RESET CIRC 3.50V SOT143-4 |
| LM2588T-ADJ/NOPB | IC REG MULTI CONFIG ADJ TO220-7 |
| MAX6468US45D3+T | IC MPU/RESET CIRC 4.50V SOT143-4 |
| LM2588S-3.3/NOPB | IC REG MULTI CONFIG 3.3V TO263-7 |
| MAX6468US25D7+T | IC MPU/RESET CIRC 2.500V SOT143 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EL7562CUZ-T13 | 功能描述:直流/直流开关转换器 2A DC-DC CNVRTR RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| EL7562CUZ-T7 | 功能描述:直流/直流开关转换器 2A DC-DC CNVRTR RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| EL7563 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Monolithic 4 Amp DC:DC Step-Down Regulator |
| EL7563C | 制造商:ELANTEC 制造商全称:ELANTEC 功能描述:Monolithic 4 Amp DC:DC Step-down Regulator |
| EL7563CM | 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。