参数资料
型号: EM6617SO28A
英文描述: Advanced Synchronous Rectified Buck MOSFET Drivers with Pre-POR OVP; Temperature Range: 0&degC to 70°C; Package: 8-EPSOIC T&R
中文描述: 微控制器
文件页数: 20/67页
文件大小: 824K
代理商: EM6617SO28A
EM6617
03/02 REV. C/442
Copyright
2002, EM Microelectronic-Marin SA
27
www.emmicroelectronic.com
8.6 Counter Setup
RegCDataL[3:0],
RegCDataM[3:0], RegCDataH[1:0]
are used to store the initial count value called
CReg[9:0]
which is written into the count register bits Count[9:0] when writing the bit Load to ‘1’ in RegCCntl2.
This bit is automatically reset thereafter. The counter value Count[9:0] can be read out at any time, except
when using non-debounced high frequency port A input clock. To maintain data integrity the lower nibble
Count[3:0]
must always be read first. The ShCount[9:4] values are shadow registers to the counter. To keep
the data integrity during a counter read operation (3 reads), the counter values [9:4] are copied into these
registers with the read of the count[3:0] register. If using non-debounced high frequency port A input the counter
must be stopped while reading the Count[3:0] value to maintain the data integrity.
In down count mode an interrupt request IRQCount0 is generated when the counter reaches 0. In up count
mode, an interrupt request is generated when the counter reaches 3FF (or FF,3F,F if limited bit counting).
Never an interrupt request is generated by loading a value into the counter register.
When the counter is programmed from up into down mode or vice versa, the counter value Count[9:0] gets
inverted. As a consequence, the initial value of the counter must be programmed after the Up/Down selection.
Loading the counter with hex 000 is equivalent to writing stop mode, the Start bit is reset, no interrupt request is
generated.
How to use the counter;
If PWM output is required one has to put the port B[3] in output mode and set PWMOn=1 in step 5.
1st,
set the counter into stop mode (Start=0).
2nd,
select the frequency and up- or down count mode in RegCCntl1.
3rd,
write the data registers RegCDataL, RegCDataM, RegCDataH (counter start value and length)
4th,
load the counter, Load=1, and choose the mode. (EvCount, EnComp=0)
5th,
select bits PWMOn in RegPresc and SelIntFull in RegSysCntl1
6th,
if compare mode desired , then write RegCDataL, RegCDataM, RegCDataH (compare value)
7th,
set bit Start and select EnComp in RegCCntl2
8.7 10-bit Counter Registers
Table 8.7.1 Register RegCCntl1
Bit
Name
Reset
R/W
Description
3
Up/Down
0
R/W
Up or down counting
2
CountFSel2
0
R/W
Input clock selection
1
CountFSel1
0
R/W
Input clock selection
0
CountFsel0
0
R/W
Input clock selection
Default : PA0 ,selected as input clock, Down counting
Table 8.7.2 Counter Input Frequency Selection with CountFSel[2..0]
CountFSel2
CountFSel1
CountFSel0
clock source selection
0
Port A
PA[0]
0
1
Prescaler Ck[15]
0
1
0
Prescaler Ck[12]
0
1
Prescaler Ck[10]
1
0
Prescaler Ck[8]
1
0
1
Prescaler Ck[4]
1
0
Prescaler Ck[1]
1
Port A
PA[3]
相关PDF资料
PDF描述
EM6617SO28B Advanced Synchronous Rectified Buck MOSFET Drivers with Pre-POR OVP; Temperature Range: -40°C to 85°C; Package: 8-EPSOIC T&R
EM6617TP28A Advanced Synchronous Rectified Buck MOSFET Drivers with Pre-POR OVP; Temperature Range: 0&degC to 70°C; Package: 8-EPSOIC T&R
EM6617TP28B Advanced Synchronous Rectified Buck MOSFET Drivers with Pre-POR OVP; Temperature Range: -40°C to 85°C; Package: 8-EPSOIC T&R
EM6640SO18A Advanced Synchronous Rectified Buck MOSFET Drivers with Pre-POR OVP; Temperature Range: -40°C to 85°C; Package: 8-SOIC
EM6640SO18B Advanced Synchronous Rectified Buck MOSFET Drivers with Pre-POR OVP; Temperature Range: -40°C to 85°C; Package: 10-DFN
相关代理商/技术参数
参数描述
EM6617SO28B 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller
EM6617TP28A 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller
EM6617TP28B 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller
EM6617WP11 制造商:EMMICRO 制造商全称:EM Microelectronic - MARIN SA 功能描述:Ultra Low Power Microcontroller with ADC AND EEPROM
EM6617WP27 制造商:EMMICRO 制造商全称:EM Microelectronic - MARIN SA 功能描述:Ultra Low Power Microcontroller with ADC AND EEPROM