- 您现在的位置：买卖IC网 > PDF目录19911 > EPC1213PI8 (Altera)IC CONFIG DEVICE 212KBIT 8-DIP PDF资料下载
参数资料
| 型号： | EPC1213PI8 |
| 厂商： | Altera |
| 文件页数： | 15/26页 |
| 文件大小： | 0K |
| 描述： | IC CONFIG DEVICE 212KBIT 8-DIP |
| 产品培训模块： | Three Reasons to Use FPGA's in Industrial Designs |
| 标准包装： | 100 |
| 系列： | EPC |
| 可编程类型： | OTP |
| 存储容量： | 212kb |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
| 配用： | PLMJ1213-ND - PROGRAMMER ADAPTER 20 PIN J-LEAD |
| 其它名称： | 544-1370-5 EPC1213PI8-ND |
Page 22
Pin Information
Configuration Devices for SRAM-Based LUT Devices
January 2012
Altera Corporation
nCS
49
10
Input
Chip select input (active low). The nCS pin connects to the
CONF
_DONE pin of the FPGA.
A low input allows DCLK to increment the address counter
and enables DATA to drive out. If the EPC1 or EPC2 device
is reset (OE pulled low) while nCS is low, the device
initializes as the master device in a configuration chain. If
the EPC1 or EPC2 device is reset (OE pulled low) while nCS
is high, the device initializes as a slave device in the chain.
The nCS pin has an internal programmable 1-k
resistor
in EPC2 devices. If internal pull-up resistors are used, do
not use external pull-up resistors on these pins. You can
disable the internal pull-up resistors through the Disable
nCS and OE pull-ups on configuration device option.
nCASC
612
15
Output
Cascade select output (active low).
This output goes low when the address counter has
reached its maximum value. When the address counter has
reached its maximum value, the configuration device has
sent all its configuration data to the FPGA. In a chain of
EPC1 or EPC2 devices, the nCASC pin of one device is
connected to the nCS pin of the next device, which permits
DCLK
to clock data from the next EPC1 or EPC2 device in
the chain. For single EPC1 or EPC2 device and the last
device in the chain, nCASC is left floating.
This pin is only available in EPC1 and EPC2 devices, which
support data cascading.
nINIT
_CONF
N/A
13
16
Open-Drain
Output
Allows the INIT_CONF JTAG instruction to initiate
configuration. The nINIT_CONF pin connects to the
nCONFIG
pin of the FPGA.
If multiple EPC2 devices are used to configure an FPGA,
the nINIT_CONF of the first EPC2 device pin is tied to the
FPGA’s nCONFIG pin, while subsequent devices'
nINIT
_CONF pins are left floating.
The INIT_CONF pin has an internal 1-k
pull-up resistor
that is always active in EPC2 devices.
This pin is only available in EPC2 devices.
TDI
N/A
11
13
Input
JTAG data input pin. Connect this pin to VCC if the JTAG
circuitry is not used.
This pin is only available in EPC2 devices.
TDO
N/A
1
28
Output
JTAG data output pin. Do not connect this pin if the JTAG
circuitry is not used.
This pin is only available in EPC2 devices.
TMS
N/A
19
25
Input
JTAG mode select pin. Connect this pin to VCC if the JTAG
circuitry is not used.
This pin is only available in EPC2 devices.
Table 20. EPC1, EPC2, and EPC1441 Device Pin Functions During Configuration (Part 2 of 3)
Pin Name
Pin Number
Pin Type
Description
8-Pin
PDIP (1)
20-Pin
PLCC
32-Pin
TQFP (2)
相关PDF资料 |
PDF描述 |
|---|---|
| EPC1PI8 | IC CONFIG DEVICE 1MBIT 8-DIP |
| ECC13DREN-S13 | CONN EDGECARD 26POS .100 EXTEND |
| EPCS16SI8N | IC CONFIG DEVICE 16MBIT 8-SOIC |
| ACC26DRYN-S734 | CONN EDGECARD 52POS DIP .100 SLD |
| NCV59301DS33R4G | IC REG LDO 3.3V 3A D2PAK-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EPC1213PI-8 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Configuration EPROM |
| EPC-12179 | 制造商:Artisan Controls Corporation 功能描述:LIGHTING CONTROLLER |
| EPC-12457 | 制造商:Artisan Controls Corporation 功能描述:Timer |
| EPC12SC36-A | 功能描述:DC/DC转换器 75 Watts 12 Volts RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| EPC13 | 制造商:TDK 制造商全称:TDK Electronics 功能描述:Ferrite Cores For Power Supply and Signal Transformer EPC Cores |
发布紧急采购，3分钟左右您将得到回复。