- 您现在的位置：买卖IC网 > PDF目录19910 > EPC4QC100N (Altera)IC CONFIG DEVICE 4MBIT 100-PQFP PDF资料下载
参数资料
| 型号： | EPC4QC100N |
| 厂商： | Altera |
| 文件页数： | 17/36页 |
| 文件大小： | 0K |
| 描述： | IC CONFIG DEVICE 4MBIT 100-PQFP |
| 产品培训模块： | Three Reasons to Use FPGA's in Industrial Designs |
| 标准包装： | 66 |
| 系列： | EPC |
| 可编程类型： | 系统内可编程 |
| 存储容量： | 4Mb |
| 电源电压： | 3 V ~ 3.6 V |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 100-BQFP |
| 供应商设备封装： | 100-PQFP（14x20） |
| 包装： | 托盘 |
| 产品目录页面： | 604 (CN2011-ZH PDF) |
| 其它名称： | 544-1378 EPC4QC100N-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
Page 24
Pin Description
Enhanced Configuration (EPC) Devices Datasheet
January 2012
Altera Corporation
WP#
Input
Usually tied to VCC or GND on the board. The controller does not drive this pin
because it could cause contention.
Connection to VCC is recommended for faster block erase or programming times
and to allow programming of the flash-bottom boot block, which is required when
programming the device using the Quartus II software.
This pin should be connected to VCC even when the external flash interface is not
used.
VCCW
Supply
Block erase, full-chip erase, word write, or lock-bit configuration power supply.
Connect this pin to the 3.3-V VCC supply, even when you are not using the external
flash interface.
RY/BY#
Open-Drain Output
Flash asserts this pin when a write or erase operation is complete. This pin is not
connected to the controller. RY/BY# is only available in Sharp flash-based EPC8
and EPC16. (2)
Leave this pin floating when the external flash interface is not used.
BYTE#
Input
Flash byte-enable pin and is only available for EPC devices in the 100-pin PQFP
package.
This pin must be connected to VCC on the board even when you are not using the
external flash interface (the controller uses the flash in 16-bit mode). For Intel
flash-based EPC device, this pin is connected to the VCCQ of the Intel flash die
internally. Therefore, BYTE# must be connected directly to VCC without using any
pull-up resistor.
Notes to Table 9:
(1) These pins can be driven to 12 V during production testing of the flash memory. Since the controller cannot tolerate the 12-V level, connections
from the controller to these pins are not made internal to the package. Instead they are available as two separate pins. You must connect the
two pins at the board level (for example, on the PCB, connect the C-WE# pin from controller to F-WE# pin from the flash memory).
(2) For more information, refer to the PCN0506: Addition of Intel Flash Memory As Source For EPC4, EPC8 and EPC16 Enhanced Configuration
Devices and Using the Intel Flash Memory-Based EPC4, EPC8 and EPC16 white paper.
Table 10. JTAG Interface Pins and Other Required Controller Pins (Part 1 of 2)
Pin Name
Pin Type
Description
TDI
Input
JTAG data input pin.
Connect this pin to VCC if the JTAG circuitry is not used.
TDO
Output
JTAG data output pin.
Do not connect this pin if the JTAG circuitry is not used (leave this pin floating).
TCK
Input
JTAG clock pin.
Connect this pin to GND if the JTAG circuitry is not used.
TMS
Input
JTAG mode select pin.
Connect this pin to VCC if the JTAG circuitry is not used.
PGM[2..0]
Input
These three input pins select one of the eight pages of configuration data to
configure the FPGAs in the system.
Connect these pins on the board to select the page specified in the Quartus II
software when generating the EPC device POF. PGM[2] is the MSB. The default
selection is page 0; PGM[2..0]=000. These pins must not be left floating.
Table 9. External Flash Interface Pins (Part 2 of 2)
Pin Name
Pin Type
Description
相关PDF资料 |
PDF描述 |
|---|---|
| V24C48H100BL | CONVERTER MOD DC/DC 48V 100W |
| XCF01SVO20C | IC PROM IN SYST PRG 3.3V 20TSSOP |
| HSC36DREH-S93 | CONN EDGECARD 72POS .100 EYELET |
| EBM15DCCS | CONN EDGECARD 30POS R/A .156 SLD |
| EPC2TC32N | IC CONFIG DEVICE 1.6MBIT 32-TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EPC4QI100 | 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 4Mb 66 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20 |
| EPC4QI100N | 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 4Mb 66 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20 |
| EPC4XXX | 制造商:ALTERA 制造商全称:Altera Corporation 功能描述:2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet |
| EPC50C605 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| EPC-525-0.5 | 制造商:EPIGAP 制造商全称:EPIGAP 功能描述:Photodiode-Chip |
发布紧急采购，3分钟左右您将得到回复。