- 您现在的位置：买卖IC网 > PDF目录19912 > EPCS4SI8N (Altera)IC CONFIG DEVICE 4MBIT 8-SOIC PDF资料下载
参数资料
| 型号： | EPCS4SI8N |
| 厂商： | Altera |
| 文件页数： | 21/40页 |
| 文件大小： | 0K |
| 描述： | IC CONFIG DEVICE 4MBIT 8-SOIC |
| 产品培训模块： | Three Reasons to Use FPGA's in Industrial Designs |
| 标准包装： | 100 |
| 系列： | EPCS |
| 可编程类型： | 系统内可编程 |
| 存储容量： | 4Mb |
| 电源电压： | 3 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
| 产品目录页面： | 604 (CN2011-ZH PDF) |
| 其它名称： | 544-1379-5 EPCS4SI8N-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
Page 28
Power and Operation
Serial Configuration (EPCS) Devices Datasheet
January 2014
Altera Corporation
Power and Operation
This section describes the power modes, power-on reset (POR) delay, error detection,
and initial programming state of the EPCS devices.
Power Mode
EPCS devices support active and standby power modes. When the nCS signal is low,
the device is enabled and is in active power mode. The FPGA is configured while the
EPCS device is in active power mode. When the nCS signal is high, the device is
disabled but remains in active power mode until all internal cycles are completed,
such as write or erase operations. The EPCS device then goes into standby power
mode. The ICC1 and ICC0 parameters list the VCC supply current when the device is in
active and standby power modes. For more information, refer to Table 21 on page 34.
Power-On Reset
During the initial power-up, a POR delay occurs to ensure the system voltage levels
have stabilized. During the AS configuration, the FPGA controls the configuration
and has a longer POR delay than the EPCS device.
f For more information about the POR delay time, refer to the configuration chapter in
the appropriate device handbook.
Error Detection
During the AS configuration with the EPCS device, the FPGA monitors the
configuration status through the nSTATUS and CONF_DONE pins. If an error condition
occurs, if the nSTATUS pin drives low or if the CONF_DONE pin does not go high, the
FPGA begins reconfiguration by pulsing the nSTATUS and nCSO signals, which controls
the chip select (nCS) pin on the EPCS device.
After an error, the configuration automatically restarts if the Auto-Restart Upon
Frame Error
option is turned on in the Quartus II software. If the option is turned off,
the system must monitor the nSTATUS signal for errors and then pulse the nCONFIG
signal low to restart configuration.
相关PDF资料 |
PDF描述 |
|---|---|
| GRM2165C2A111JA01D | CAP CER 110PF 100V 5% NP0 0805 |
| RCB92DHRR-S330 | EDGECARD EXT PCI 184PS .050 3.3V |
| FMC18DREH | CONN EDGECARD 36POS .100 EYELET |
| 1250L4 | BATTERY PK S-HD 6.0V D SIZE ZINC |
| EPC1PC8 | IC CONFIG DEVICE 1MBIT 8-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EPCS4SI8N | 制造商:Altera Corporation 功能描述:SEMICONDUCTOR ((NW)) |
| EPCS64 | 制造商:ALTERA 制造商全称:Altera Corporation 功能描述:Serial Configuration Devices |
| EPCS64SI16N | 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 64Mb 40 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20 |
| EPCSC2.5T | 功能描述:接线端子工具和配件 End Plate RoHS:否 制造商:Phoenix Contact 产品:Tools & Accessories 类型:End Bracket |
| EPCSC2.5T1-2 | 功能描述:接线端子工具和配件 End Plate RoHS:否 制造商:Phoenix Contact 产品:Tools & Accessories 类型:End Bracket |
发布紧急采购，3分钟左右您将得到回复。