- 您现在的位置：买卖IC网 > PDF目录97930 > EPL43102 Graphic STN LCD Drivers with Built-in RAM PDF资料下载
参数资料
| 型号： | EPL43102 |
| 英文描述： | Graphic STN LCD Drivers with Built-in RAM |
| 中文描述： | 图形STN液晶显示器驱动器，内置内存 |
| 文件页数： | 5/64页 |
| 文件大小： | 280K |
| 代理商： | EPL43102 |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
43 COM / 102 SEG LCD DRIVER
The information in this document is subject to change without notice.
8
OSC
I
When using an external oscillator, input the clock to OSC pin.
When using an internal oscillator, leave this pin open.
FRS
O
Static driver output pin.
This pin is used in combination with the FR pin.
IRS
I
Internal resistor select pin.
This pin selects the resistors for adjusting V0 voltage level and is
available only in master mode.
- IRS = "H": The internal resistors are used.
- IRS = "L": The external resistors are used. V0 voltage is controlled
using the external divider resistor connect the VR pin.
MPU INTERFACE
Name
I/O
Description
/RES
I
Hardware reset input.
The LSI is reset when this signal is pulled low. (Active low)
These are the chip select signals. The Chip Select of the LSI
becomes active when CS1 is "L" and also CS2 is "H" and allows the
input/output of data or commands.
/CS1
CS2
Status
“L”
The device is not active. (D7~D0 is Hi-Z)
“L”
“H”
Data and instruction are available.
“H”
“L”
The device is not active. (D7~D0 is Hi-Z)
“H”
The device is not active. (D7~D0 is Hi-Z)
/CS1,CS2
I
A0
I
Used as register selection input.
When A0 = "High", Data register.
When A0 = "Low", Instruction register.
/WR (R/W)
I
When C68 = "High"(68-series MPU interfacing), used as
read (/WR = "High"),write (/WR = "Low")
When C68 = "Low "(80-series MPU interfacing), used as write
enable input (/WR).
/RD (E)
I
When C68 = "High"(68-series MPU interfacing), used as read/write
enable input (E).
When C68 = "Low "(80-series MPU interfacing), used as read enable
input (/RD).
D0 to D7
I/O
When serial mode, D6 (SCK) is used as serial clock input pin, D7
(SDI) is used as serial data input pin, D5 (SDO) is used as serial
data output pin and the others are not used.
When
parallel mode, D0 to D7 are used as bi-directional data bus
pin.
相关PDF资料 |
PDF描述 |
|---|---|
| EPL65132 | Graphic STN LCD Drivers with Built-in RAM |
| EPM3032ALC44-10 | Electrically-Erasable Complex PLD |
| EPM3032ALC44-4 | Eval Board for ISL6118 2.5V to 5V Dual Power Supply Controller with 0.6A Integrated Current Regulation and Timed Delay to Latch-off |
| EPM3032ALC44-7 | Electrically-Erasable Complex PLD |
| EPM3032ATC44-10 | |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EPL-60 | 功能描述:PAPER THERMAL PRINTER 60 MM RoHS:否 类别:计算机，办公室 - 元件，配件 >> 配件 系列:- 标准包装:1 系列:- 附件类型:替代墨盒 技术规格:- 适用于相关产品:- 其它名称:CMS-INK-RO-C5 |
| EPL6024-102 | 制造商:Coilcraft Inc 功能描述:Power inductor, shielded, 20% tol, SMT, RoHS, halogen-free |
| EPL6024-102ME | 制造商:Coilcraft Inc 功能描述:Power inductor, shielded, 20% tol, SMT, RoHS, halogen-free |
| EPL6024-102MEB | 功能描述:固定电感器 Power Inductor 1 uH 20 % 12.5 A RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm |
| EPL6024-102MEC | 功能描述:固定电感器 Power Inductor 1 uH 20 % 12.5 A RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm |
发布紧急采购，3分钟左右您将得到回复。