参数资料
型号: EPM7032BLC44-3
厂商: Altera
文件页数: 18/66页
文件大小: 0K
描述: IC MAX 7000 CPLD 32 44-PLCC
标准包装: 130
系列: MAX® 7000B
可编程类型: 系统内可编程
最大延迟时间 tpd(1): 3.5ns
电压电源 - 内部: 2.375 V ~ 2.625 V
逻辑元件/逻辑块数目: 2
宏单元数: 32
门数: 600
输入/输出数: 36
工作温度: 0°C ~ 70°C
安装类型: 表面贴装
封装/外壳: 44-LCC(J 形引线)
供应商设备封装: 44-PLCC(16.58x16.58)
包装: 管件
Altera Corporation
25
MAX 7000B Programmable Logic Device Data Sheet
Programmable Pull-Up Resistor
Each MAX 7000B device I/O pin provides an optional programmable
pull-up resistor during user mode. When this feature is enabled for an I/O
pin, the pull-up resistor (typically 50 k) weakly holds the output to
VCCIO level.
Bus Hold
Each MAX 7000B device I/O pin provides an optional bus-hold feature.
When this feature is enabled for an I/O pin, the bus-hold circuitry weakly
holds the signal at its last driven state. By holding the last driven state of
the pin until the next input signals is present, the bus-hold feature can
eliminate the need to add external pull-up or pull-down resistors to hold
a signal level when the bus is tri-stated. The bus-hold circuitry also pulls
undriven pins away from the input threshold voltage where noise can
cause unintended high-frequency switching. This feature can be selected
individually for each I/O pin. The bus-hold output will drive no higher
than VCCIO to prevent overdriving signals. The propagation delays
through the input and output buffers in MAX 7000B devices are not
affected by whether the bus-hold feature is enabled or disabled.
The bus-hold circuitry weakly pulls the signal level to the last driven state
through a resistor with a nominal resistance (RBH) of approximately
8.5 k. Table 12 gives specific sustaining current that will be driven
through this resistor and overdrive current that will identify the next
driven input level. This information is provided for each VCCIO voltage
level.
The bus-hold circuitry is active only during user operation. At power-up,
the bus-hold circuit initializes its initial hold value as VCC approaches the
recommended operation conditions. When transitioning from ISP to User
Mode with bus hold enabled, the bus-hold circuit captures the value
present on the pin at the end of programming.
Table 12. Bus Hold Parameters
Parameter
Conditions
VCCIO Level
Units
1.8 V
2.5 V
3.3 V
MinMax
Low sustaining current
VIN > VIL (max)
30
50
70
μA
High sustaining current
VIN < VIH (min)
–30
–50
–70
μA
Low overdrive current
0 V < VIN < VCCIO
200
300
500
μA
High overdrive current
0 V < VIN < VCCIO
–295
–435
–680
μA
相关PDF资料
PDF描述
PQ015ENA1ZZH IC REG LDO 1.5V 1A SC-63
VI-2TZ-CY-F3 CONVERTER MOD DC/DC 2V 20W
180-M26-203L021 CONN DB26 FMAL HD SLD CUP NICKEL
NDL0512SC CONV DC/DC 2W 5VIN 12VOUT SIP
ECC08DCMH CONN EDGECARD 16POS .100 WW
相关代理商/技术参数
参数描述
EPM7032BLC44-5 制造商:Rochester Electronics LLC 功能描述: 制造商:Altera Corporation 功能描述:
EPM7032BLC44-7 制造商:Rochester Electronics LLC 功能描述: 制造商:Altera Corporation 功能描述:
EPM7032BTC44-3 制造商:Altera Corporation 功能描述:IC MAX
EPM7032BTC44-3N 制造商:Altera Corporation 功能描述:IC MAX
EPM7032BTC44-5 制造商:Altera Corporation 功能描述:CPLD MAX 7000B Family 600 Gates 32 Macro Cells 212.8MHz CMOS Technology 2.5V 44-Pin TQFP