- 您现在的位置：买卖IC网 > PDF目录16568 > EVAL-AD2S1205SDZ (Analog Devices Inc)BOARD EVAL FOR AD2S1205 PDF资料下载
参数资料
| 型号： | EVAL-AD2S1205SDZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 6/20页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD2S1205 |
| 标准包装： | 1 |
| 主要目的： | 接口，旋转变压至数字 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | AD2S1205 |
| 主要属性： | 12 位分辨率，最大 1250 rps 或 1024 脉冲/反向 |
| 已供物品： | 板 |
AD2S1205
Rev. A | Page 14 of 20
SERIAL INTERFACE
The angular position and velocity are available on the AD2S1205
in two 12-bit registers. These registers can be accessed via a 3-wire
serial interface (SO, RD, and SCLK) that operates at clock rates
of up to 25 MHz and is compatible with SPI and DSP interface
standards. The serial interface is selected by holding the SOE pin
low. Data from the position and velocity integrators are first trans-
ferred to the position and velocity registers using the SAMPLE pin.
The RDVEL pin selects whether data is transferred from the
position or velocity register to the output register, and the CS pin
must be held low to transfer data from the selected register to the
output register. Finally, the RD input is used to read the data that
is clocked out of the output register and is available on the serial
output pin (SO). When the serial interface is selected, DB11 is used
as the serial output pin (SO), DB10 is used as the serial clock input
(SCLK), and Pin DB0 to Pin DB9 are placed into the high imped-
ance state. The timing requirements for the read cycle are described
in
.
SO Output
The output shift register is 16 bits wide. Data is clocked out of
the device as a 16-bit word by the serial clock input (SCLK).
The timing diagram for this operation is shown in Figure 8.
The 16-bit word consists of 12 bits of angular data (position or
velocity, depending on RDVEL input), one RDVEL status bit,
and three status bits (a parity bit, a degradation of signal bit, and
a loss of tracking bit). Data is clocked out MSB first from the
SO pin, beginning with DB15. DB15 through DB4 correspond
to the angular information. The angular position data format
is unsigned binary, with all 0s corresponding to 0° and all 1s cor-
responding to 360° l LSB. The angular velocity data format
is twos complement, with the MSB representing the rotation
direction. DB3 is the RDVEL status bit, with a 1 indicating
position and a 0 indicating velocity. DB2 is DOS, the degradation
of signal flag (refer to the
section). Bit 1
is LOT, the loss of tracking flag (refer to the
section). Bit 0 is PAR, the parity bit. The position and
velocity data are in odd parity format, and the data readback
always contains an odd number of logic highs (1s).
SAMPLE Input
Data is transferred from the position and velocity integrators to
the position and velocity registers, respectively, after a high-to-
low transition on the SAMPLE signal. This pin must be held low
for at least t1 to guarantee correct latching of the data. RD should
not be pulled low before this time because data will not be ready.
The converter continues to operate during the read process.
CS Input
The device is enabled when CS is held low.
RD Input
The 12-bit data bus lines are normally in a high impedance
state. The output buffer is enabled when CS and RD are held
low. The RD input is an edge-triggered input that acts as a frame
synchronization signal and an output enable. On a falling edge of
the RD signal, data is transferred to the output buffer. Data is
then available on the serial output pin (SO); however, it is only
valid after RD is held low for t9. The serial data is clocked out
of the SO pin on the rising edges of SCLK, and each data bit is
available at the SO pin on the falling edge of SCLK. However,
as the MSB is clocked out by the falling edge of RD, the MSB is
available at the SO pin on the first falling edge of SCLK. Each
subsequent bit of the data-word is shifted out on the rising edge
of SCLK and is available at the SO pin on the falling edge of
SCLK for the next 15 clock pulses.
The high-to-low transition of RD must occur during the high
time of the SCLK to avoid DB14 being shifted on the first rising
edge of the SCLK, which would result in the MSB being lost.
RD may rise high after the last falling edge of SCLK. If RD is
held low and additional SCLKs are applied after DB0 has been
read, then 0s will be clocked from the data output. When
reading data continuously, wait a minimum of t5 after RD
is released before reapplying it.
RDVEL Input
RDVEL input is used to select between the angular position
register and the angular velocity register. RDVEL is held high to
select the angular position register and low to select the angular
velocity register. The RDVEL pin must be set (stable) at least t4
before the RD pin is pulled low.
相关PDF资料 |
PDF描述 |
|---|---|
| EBM25DCCI-S189 | CONN EDGECARD 50POS R/A .156 SLD |
| RCC15DCMT-S288 | CONN EDGECARD 30POS .100 EXTEND |
| EMM06DTMT-S189 | CONN EDGECARD 12POS R/A .156 SLD |
| L-14C12NKV4T | CER INDUCTOR 12NH 0603 |
| GBC10DRAN-S734 | CONN EDGECARD 20POS .100 R/A SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD2S1210EDZ | 功能描述:BOARD EVAL AD2S1210 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PSoC® 主要目的:电源管理，热管理 嵌入式:- 已用 IC / 零件:- 主要属性:- 次要属性:- 已供物品:板，CD，电源 |
| EVAL-AD4001FMCZ | 功能描述:EVAL BOARD FOR AD4001 制造商:analog devices inc. 系列:- 零件状态:在售 A/D 转换器数:1 位数:16 采样率（每秒）:2M 数据接口:SPI，DSP 输入范围:±VREF 不同条件下的功率（典型值）:20mW @ 2MSPS 使用的 IC/零件:AD4001 所含物品:板，电源 标准包装:1 |
| EVAL-AD421EB | 制造商:AD 制造商全称:Analog Devices 功能描述:Loop-Powered 4 mA to 20 mA DAC |
| EVAL-AD5025EBZ | 制造商:AD 制造商全称:Analog Devices 功能描述:Fully Accurate 12-/14-/16-Bit VOUT DAC SPI Interface 2.7 V to 5.5 V in a TSSOP |
| EVAL-AD5045EBZ | 制造商:AD 制造商全称:Analog Devices 功能描述:Fully Accurate 12-/14-/16-Bit VOUT DAC SPI Interface 2.7 V to 5.5 V in a TSSOP |
发布紧急采购，3分钟左右您将得到回复。