- 您现在的位置：买卖IC网 > PDF目录16593 > EVAL-AD5235SDZ (Analog Devices Inc)BOARD EVAL FOR AD5235 PDF资料下载
参数资料
| 型号： | EVAL-AD5235SDZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 16/32页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD5235 |
| 标准包装： | 1 |
| 主要目的： | 数字电位器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | AD5235 |
| 主要属性： | 2 沟道，1024 位置 |
| 次要属性： | SPI 接口 |
| 已供物品： | 板，CD |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
Data Sheet
AD5235
Rev. F | Page 23 of 32
Because the AD5235 can also be supplied by dual supplies, the
general equation defining the output voltage at VW with respect
to ground for any given input voltages applied to Terminal A
and Terminal B is
B
AB
W
V
D
V
+
×
=
1024
)
(
(3)
Equation 3 assumes that VW is buffered so that the effect of wiper
resistance is minimized. Operation of the digital potentiometer in
divider mode results in more accurate operation over temperature.
Here, the output voltage is dependent on the ratio of the internal
resistors and not the absolute value; therefore, the drift improves
to 15 ppm/°C. There is no voltage polarity restriction between
Terminal A, Terminal B, and Terminal W as long as the
terminal voltage (VTERM) stays within VSS < VTERM < VDD.
PROGRAMMING EXAMPLES
The following programming examples illustrate a typical sequence
of events for various features of the AD5235. See Table 7 for the
instructions and data-word format. The instruction numbers,
addresses, and data appearing at the SDI and SDO pins are in
hexadecimal format.
Table 14. Scratchpad Programming
SDI
SDO
Action
0xB00100
0xXXXXXX
Writes Data 0x100 into RDAC1 register,
Wiper W1 moves to 1/4 full-scale
position.
0xB10200
0xB00100
Loads Data 0x200 into RDAC2 register,
Wiper W2 moves to 1/2 full-scale
position.
Table 15. Incrementing RDAC Followed by Storing the
Wiper Setting to EEMEM
SDI
SDO
Action
0xB00100
0xXXXXXX
Writes Data 0x100 into RDAC1
register, Wiper W1 moves to 1/4 full-
scale position.
0xE0XXXX
0xB00100
Increments RDAC1 register by one to
0x101.
0xE0XXXX
Increments RDAC1 register by one to
0x102. Continue until desired wiper
position is reached.
0x20XXXX
0xXXXXXX
Stores RDAC2 register data into
EEMEM1. Optionally, tie WP to GND to
protect EEMEM values.
The EEMEM values for the RDACs can be restored by power-
on, by strobing the PR pin, or by the two commands shown in
Table 16. Restoring the EEMEM Values to RDAC Registers
SDI
SDO
Action
0x10XXXX
0xXXXXXX
Restores the EEMEM1 value to the
RDAC1 register.
Table 17. Using Left-Shift by One to Increment 6 dB Steps
SDI
SDO
Action
0xC0XXXX
0xXXXXXX
Moves Wiper 1 to double the
present data contained in the
RDAC1 register.
0xC1XXXX
0xC0XXXX
Moves Wiper 2 to double the
present data contained in the
RDAC2 register.
Table 18. Storing Additional User Data in EEMEM
SDI
SDO
Action
0x32AAAA
0xXXXXXX
Stores Data 0xAAAA in the extra
EEMEM location USER1. (Allowable to
address in 13 locations with a
maximum of 16 bits of data.)
0x335555
0x32AAAA
Stores Data 0x5555 in the extra
EEMEM location USER2. (Allowable to
address in 13 locations with a
maximum of 16 bits of data.)
Table 19. Reading Back Data from Memory Locations
SDI
SDO
Action
0x92XXXX
0xXXXXXX
Prepares data read from USER1
EEMEM location.
0x00XXXX
0x92AAAA
NOP Instruction 0 sends a 24-bit word
out of SDO, where the last 16 bits
contain the contents in USER1 EEMEM
location.
Table 20. Reading Back Wiper Settings
SDI
SDO
Action
0xB00200
0xXXXXXX
Writes RDAC1 to midscale.
0xC0XXXX
0xB00200
Doubles RDAC1 from midscale to full
scale.
0xA0XXXX
0xC0XXXX
Prepares reading wiper setting from
RDAC1 register.
0xXXXXXX
0xA003FF
Reads back full-scale value from SDO.
EVAL-AD5235SDZ EVALUATION KIT
Analog Devices, Inc., offers a user-friendly EVAL-AD5235SDZ
evaluation kit that can be controlled by a PC in conjunction
with the SDP platform. The driving program is self-contained;
no programming languages or skills are needed.
相关PDF资料 |
PDF描述 |
|---|---|
| MCZ33742EGR2 | IC SYSTEM BASIS CHIP CAN 28-SOIC |
| ECM30DCAN | CONN EDGECARD 60POS R/A .156 SLD |
| EVAL-ADCMP561BRQZ | BOARD EVALUATION ADCMP561BRQZ |
| VI-BNB-EW | CONVERTER MOD DC/DC 95V 100W |
| A3AAB-2036M | IDC CABLE- ASC20B/AE20M/ASC20B |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD5235SDZ | 制造商:Analog Devices 功能描述:Evaluation board |
| EVAL-AD5242EBZ | 功能描述:BOARD EVALUATION FOR AD5242 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| EVAL-AD5243SDZ | 功能描述:BOARD EVAL FOR AD5243 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:* 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| EVAL-AD5245EBZ | 功能描述:EVAL BOARD FOR AD5245 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| EVAL-AD5246DBZ | 功能描述:BOARD EVAL FOR AD5246DBZ RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:* 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
发布紧急采购，3分钟左右您将得到回复。