- 您现在的位置：买卖IC网 > PDF目录17075 > EVAL-AD5361EBZ (Analog Devices Inc)BOARD EVAL FOR AD5361 PDF资料下载
参数资料
| 型号： | EVAL-AD5361EBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 13/29页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD5361 |
| 产品培训模块： | DAC Architectures |
| 标准包装： | 1 |
| DAC 的数量： | 16 |
| 位数： | 14 |
| 采样率（每秒）： | 540k |
| 数据接口： | 串行 |
| 设置时间： | 20µs |
| DAC 型： | 电压 |
| 工作温度： | -40°C ~ 85°C |
| 已供物品： | 板，CD |
| 已用 IC / 零件： | AD5361 |
| 相关产品： | AD5361BSTZ-REEL-ND - IC DAC 14BIT 16CH SERIAL 52-LQFP AD5361BSTZ-ND - IC DAC 14BIT 16CH SERIAL 56LQFP AD5361BCPZ-REEL7-ND - IC DAC 14BIT 16CH SERIAL 56LFCSP AD5361BCPZ-ND - IC DAC 14BIT 16CH SERIAL 56LFCSP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
AD5360/AD5361
Rev. A | Page 19 of 28
RESET FUNCTION
The reset function is initiated by the RESET pin. On the rising
edge of RESET, the AD5360/AD5361 state machine initiates a
reset sequence to reset the X, M, and C registers to their default
values. This sequence typically takes 300 μs, and the user should
not write to the part during this time. On power-up, it is recom-
mended that the user bring RESET high as soon as possible to
properly initialize the registers.
When the reset sequence is complete (and provided that CLR is
high), the DAC output is at a potential specified by the default
register settings, which are equivalent to SIGGNDx. The DAC
outputs remain at SIGGNDx until the X, M, or C register is
updated and LDAC is taken low. The AD5360/AD5361 can be
returned to the default state by pulsing RESET low for at least
30 ns. Note that, because the reset function is rising edge trig-
gered, bringing RESET low has no effect on the operation of
the AD5360/AD5361.
CLEAR FUNCTION
CLR is an active low input that should be high for normal
operation. The CLR pin has an internal 500 kΩ pull-down
resistor. When CLR is low, the input to each of the DAC output
buffer stages (VOUT0 to VOUT15) is switched to the externally
set potential on the relevant SIGGNDx pin. While CLR is low,
all LDAC pulses are ignored. When CLR is taken high again, the
DAC outputs return to their previous values. The contents of
input registers and DAC Register 0 to DAC Register 15 are not
affected by taking CLR low. To prevent glitches appearing on
the outputs, CLR should be brought low whenever the output
span is adjusted by writing to the offset DAC.
BUSY AND LDAC FUNCTIONS
The value of an X2 (A or B) register is calculated each time the
user writes new data to the corresponding X1, C, or M register.
During the calculation of X2, the BUSY output goes low. While
BUSY is low, the user can continue writing new data to the X1,
M, or C register (see the Register Update Rates section for more
details), but no DAC output updates can take place.
The BUSY pin is bidirectional and has a 50 kΩ internal pull-up
resistor. When multiple AD5360 or AD5361 devices may be
used in one system, the BUSY pins can be tied together. This is
useful when it is required that no DAC in any device be updated
until all other DACs are ready. When each device has finished
updating the X2 (A or B) register, it releases the BUSY pin. If
another device has not finished updating its X2 registers, it
holds BUSY low, thus delaying the effect of LDAC going low.
The DAC outputs are updated by taking the LDAC input low. If
LDAC goes low while BUSY is active, the LDAC event is stored
and the DAC outputs update immediately after BUSY goes
high. A user can also hold the LDAC input permanently low. In
this case, the DAC outputs update immediately after BUSY goes
high. Whenever the A/B select registers are written to, BUSY
also goes low, for approximately 600 ns.
The AD5360/AD5361 have flexible addressing that allows
writing of data to a single channel, all channels in a group, the
same channel in Group 0 and Group 1, or all channels in the
device. This means that 1, 2, 8, or 16 DAC register values may
need to be calculated and updated. Because there is only one
multiplier shared among 16 channels, this task must be done
sequentially, so the length of the BUSY pulse varies according to
the number of channels being updated.
Table 8. BUSY Pulse Widths
Action
BUSY Pulse Width1
Loading Input, C, or M to 1 Channel2
1.5 μs maximum
Loading Input, C, or M to 2 Channels
2.1 μs maximum
Loading Input, C, or M to 8 Channels
5.7 μs maximum
Loading Input, C, or M to 16 Channels
10.5 μs maximum
1
BUSY pulse width = ((number of channels + 1) × 600 ns) + 300 ns.
2 A single channel update is typically 1 μs.
The AD5360/AD5361 contain an extra feature whereby a DAC
register is not updated unless its X2A or X2B register has been
written to since the last time LDAC was brought low. Normally,
when LDAC is brought low, the DAC registers are filled with
the contents of the X2A or X2B registers, depending on the
setting of the A/B select register. However, the AD5360/
AD5361 update the DAC register only if the X2A or X2B data has
changed, thereby removing unnecessary digital crosstalk.
BIN/2SCOMP PIN
The BIN/2SCOMP pin determines if the output data is presented
as offset binary or twos complement. If this pin is low, the data
is straight binary. If it is high, the data is twos complement. This
affects only the X, C, and offset DAC registers; the M register
and the control and command data are interpreted as straight
binary.
TEMPERATURE SENSOR
The on-chip temperature sensor provides a voltage output
at the TEMP_OUT pin that is linearly proportional to the
Centigrade temperature scale. The typical accuracy of the
temperature sensor is ±1°C at +25°C and ±5°C over the 40°C
to +85°C range. Its nominal output voltage is 1.46 V at +25°C,
varying at 4.4 mV/°C. Its low output impedance, low self-
heating, and linear output simplify interfacing to temperature
control circuitry and analog-to-digital converters.
相关PDF资料 |
PDF描述 |
|---|---|
| V300C2E50BF3 | CONVERTER MOD DC/DC 2V 50W |
| 0210490910 | CABLE JUMPER 1.25MM .178M 21POS |
| V24C5E125BL2 | CONVERTER MOD DC/DC 5V 125W |
| EVAL-AD5433EBZ | BOARD EVAL FOR AD5433 |
| HCC08DRES-S13 | CONN EDGECARD 16POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD5361EBZ1 | 制造商:AD 制造商全称:Analog Devices 功能描述:16-Channel, 16-/14-Bit, Serial Input, Voltage-Output DAC |
| EVAL-AD5362EBZ | 功能描述:BOARD EVAL FOR AD5362 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5363EBZ | 功能描述:BOARD EVALUATION FOR AD5363 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5370EBZ | 功能描述:BOARD EVALUATION FOR AD5370 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5371EBZ | 功能描述:BOARD EVAL FOR AD5371 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
发布紧急采购，3分钟左右您将得到回复。