- 您现在的位置：买卖IC网 > PDF目录16871 > EVAL-AD5520EBZ (Analog Devices Inc)BOARD EVAL FOR AD5520 PDF资料下载
参数资料
| 型号： | EVAL-AD5520EBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 7/24页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD5520 |
| 标准包装： | 1 |
| 主要目的： | 测试与测量，每引脚参数测量单元（PPMU） |
| 已用 IC / 零件： | AD5520 |
| 已供物品： | 板 |
| 相关产品： | AD5520JSTZ-ND - IC PPMU SNGL-CH 64-LQFP |
AD5520
Rev. B | Page 15 of 24
FORCE CONTROL AMPLIFIER
The force control amplifier requires external capacitors
connected between the COMPOUTx and COMPINx pins.
For stability with large capacitance at the DUT, the largest
capacitance value (3000 pF) should be selected. The force
control amplifier should always contribute the dominant
pole in the control loop. Settling times increase with
larger capacitances. ACx inputs select which external
compensation capacitor is used.
Table 10. AC0, AC1 Compensation Capacitor Selection
AC0
AC1
Function
Low
Select External Compensation Capacitor 0
High
Low
Select External Compensation Capacitor 1
Low
High
Select External Compensation Capacitor 2
COMPARATOR FUNCTION AND STROBING
The AD5520 has an on-board window comparator that
provides two bits of useful information, DUT too low or
DUT too high. CPSEL is the digital input that controls
this function, selecting whether it should compare to the
voltage sense or the current sense amplifier.
Table 11. Comparator Function Select
CPSEL
Function
Low
Compare CPL, CPH to MEASVOUT
High
Compare CPL, CPH to MEASIOUT
After CPSEL has selected which amplifier output is of interest,
logic input CPCK is used to initiate comparator sampling and
update the logic outputs CPOH and CPOL. This indicates
whether the voltages at MEASIOUT or MEASVOUT have
exceeded voltages set at CPL or CPH (thus providing DUT too
high or DUT too low information). A rising edge on STB is
required to clock the CPOH and CPOL data out.
Table 12. CPCK Synchronous Logic Outputs
CPOH
Function
Low
High
MEASVOUT or MEASIOUT < CPH MEASVOUT or
MEASIOUT > CPH
CPOL
Function
Low
High
MEASVOUT or MEASIOUT > CPL MEASVOUT or
MEASIOUT < CPL
CLAMP FUNCTION
Clamp circuitry, which is also included on-chip, clamps the
force amplifier’s output if the voltage or current applied to the
DUT exceeds the clamp levels, CLL and CLH. The clamp
circuitry also comes into play in the event of a short or open
circuit. When in force current range, the voltage clamps protect
the DUT from an open circuit. Likewise, when forcing a voltage
and a short circuit occurs, the current clamps protect the DUT.
The clamps also function to protect the DUT if a transient
voltage or current spike occurs when changing to a different
operating mode, or when programming the device to a different
current range.
The digital output flags, which indicate a clamp limit has been
hit, are CLHDETECT for the upper clamp, and CLLDETECT
output for the lower clamp.
Table 13. Clamp Detect Outputs
CLHDETECT
Function
Low
Upper Clamp Inactive
High
Upper Clamp Active
CLLDETECT
Function
Low
Lower Clamp Inactive
High
Lower Clamp Active
HIGH CURRENT RANGES
With the use of an external high current amplifier, two high
current ranges are possible. The current range values can be set
as required in the application through appropriate selection of
the sense resistors connected between MEASI5H, MEASI4H,
and MEASIL. When one of these high current ranges (Mode 4
or Mode 5) is selected via the AMx control lines, the appro-
priate QM4 or QM5 output is enabled. As a result, these outputs
can be used to control relays connected in series with the high
current amplifier, as shown in Figure 26.
Table 14. High Current Range Logic Outputs
QM4
QM5
Function
High
Low
Current Range Mode 4 Enable Output
Low
High
Current Range Mode 5 Enable Output
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6198AESA+T | IC VREF SERIES PREC 4.096V 8SOIC |
| QPI-5-EVAL1 | EVALUATION BOARD FOR QPI-5 |
| H6MMH-4006M | DIP CABLE - HDM40H/AE40M/HDM40H |
| QPO-2-EVAL1 | EVALUATION BOARD FOR QPO-2 |
| RP60-2415SG | CONV DC/DC 60W 18-36VIN 15VOUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD5522EBDZ | 功能描述:BOARD EVAL FOR 14X14MM AD5522 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PSoC® 主要目的:电源管理，热管理 嵌入式:- 已用 IC / 零件:- 主要属性:- 次要属性:- 已供物品:板，CD，电源 |
| EVAL-AD5522EBUZ | 功能描述:BOARD EVAL FOR 12X12MM AD5522 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| EVAL-AD5532EB | 制造商:AD 制造商全称:Analog Devices 功能描述:32-Channel Infinite Sample-and-Hold |
| EVAL-AD5532EBZ | 功能描述:BOARD EVAL FOR AD5532 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5532HSEBZ | 功能描述:BOARD EVAL FOR AD5532HS RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
发布紧急采购，3分钟左右您将得到回复。