- 您现在的位置：买卖IC网 > PDF目录17076 > EVAL-AD5570SDZ (Analog Devices Inc)BOARD EVAL FOR AD5570 PDF资料下载
参数资料
| 型号： | EVAL-AD5570SDZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 2/24页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD5570 |
| 标准包装： | 1 |
| DAC 的数量： | 1 |
| 位数： | 16 |
| 采样率（每秒）： | 83k |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 设置时间： | 12µs |
| DAC 型： | 电压 |
| 工作温度： | -40°C ~ 85°C |
| 已供物品： | 板 |
| 已用 IC / 零件： | AD5570 |
AD5570
Rev. C | Page 10 of 24
TERMINOLOGY
Relative Accuracy or Integral Nonlinearity (INL)
Relative accuracy or integral nonlinearity is a measure of
the maximum deviation, in LSBs, from a straight line pass-
ing through the endpoints of the DAC transfer function.
Monotonicity
A DAC is monotonic if the output either increases or remains
constant for increasing digital inputs. The AD5570 is mono-
tonic over its full operating temperature range.
Differential Nonlinearity (DNL)
Differential nonlinearity is the difference between the measured
change and the ideal 1 LSB change between any two adjacent codes.
A specified differential nonlinearity of ±1 LSB maximum ensures
monotonicity.
Gain Error
Gain error is the difference between the actual and ideal analog
output range, expressed as a percent of the full-scale range. It is
the deviation in slope of the DAC transfer characteristic from
the ideal.
Gain Error Temperature Coefficient
Gain error temperature coefficient is a measure of the change in
gain error with changes in temperature. It is expressed in ppm/°C.
Negative Full-Scale Error/Zero Scale Error
Negative full-scale error is the error in the DAC output voltage
when all 0s are loaded into the DAC latch. Ideally, the output
voltage, with all 0s in the DAC latch, is 2 VREF.
Full-Scale Error
Full-scale error is the error in the DAC output voltage when all
1s are loaded to the DAC latch. Ideally, the output voltage with
all 1s loaded into the DAC latch is 2 VREF 1 LSB.
Bipolar Zero Error
Bipolar zero error is the deviation of the analog input from the
ideal half-scale output of 0.0000 V when the inputs are loaded
with 0x8000.
Output Voltage Settling Time
Output voltage settling time is the amount of time it takes for
the output to settle to a specified level for a full-scale input change.
Slew Rate
The slew rate of a device is a limitation in the rate of change of
output voltage. The output slewing speed of a voltage-output
DAC converter is usually limited by the slew rate of the ampli-
fier used at its output. Slew rate is measured from 10% to 90%
of the output signal and is given in V/μs.
Digital-to-Analog Glitch Impulse
Digital-to-analog glitch impulse is the amount of charge injected
into the analog output when the input codes in the DAC register
change state. It is specified as the area of the glitch in nV-s and
is measured when the digital input code changes by 1 LSB at the
major carry transition, that is, from code 0x7FFF to 0x8000.
Bandwidth
The reference amplifiers within the DAC have a finite band-
width to optimize noise performance. To measure it, a sine
wave is applied to the reference input (REFIN), with full-scale
code loaded to the DAC. The bandwidth is the frequency at
which the output amplitude falls to 3 dB below the input.
Digital Feedthrough
Digital feedthrough is a measure of the impulse injected into
the analog output of the DAC from the digital inputs of the
DAC, but is measured when the DAC output is not updated.
SYNC is held high, while the SCLK and SDIN signals are tog-
gled. Digital feedthrough is specified in nV-s and is measured
with a full-scale code change on the data bus, that is, from all
0s to all 1s, and vice versa.
Power Supply Sensitivity
Power supply sensitivity indicates how the output of the DAC is
affected by changes in the power supply voltage.
相关PDF资料 |
PDF描述 |
|---|---|
| FPF2006 | IC SWITCH LOAD FULL FUNC SC70-5 |
| UCS2G680MNY9 | CAP ALUM 68UF 400V 20% RADIAL |
| UPB2D391MRD | CAP ALUM 390UF 200V 20% RADIAL |
| MIC94095YMT TR | IC LOAD SW HGH SIDE 1.2A 4-TMLF |
| LGU2G121MELZ | CAP ALUM 120UF 400V 20% SNAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD5590EBZ | 功能描述:BOARD EVAL FOR AD5590 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD5620EB | 制造商:AD 制造商全称:Analog Devices 功能描述:Single, 12-/14-/16-Bit nanoDAC with 5 ppm/C On-Chip Reference in SOT-23 |
| EVAL-AD5620EBZ | 功能描述:EVAL BOARD FOR AD5620 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:nanoDAC™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5621EBZ | 功能描述:BOARD EVALUATION FOR AD5621 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:nanoDAC™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5629REBRZ | 功能描述:BOARD EVAL FOR AD5629 TSSOP RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:denseDAC 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
发布紧急采购，3分钟左右您将得到回复。