- 您现在的位置：买卖IC网 > PDF目录17065 > EVAL-AD5757SDZ (Analog Devices Inc)BOARD EVAL FOR AD5757 PDF资料下载
参数资料
| 型号： | EVAL-AD5757SDZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 32/44页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD5757 |
| 标准包装： | 1 |
| DAC 的数量： | 4 |
| 位数： | 16 |
| 数据接口： | 串行 |
| 设置时间： | 15µs |
| DAC 型： | 电流 |
| 工作温度： | -40°C ~ 105°C |
| 已供物品： | 板 |
| 已用 IC / 零件： | AD5757 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
AD5757
Data Sheet
Rev. D | Page 38 of 44
DC-to-DC Converter Compensation Capacitors
As the dc-to-dc converter operates in DCM, the uncompensated
transfer function is essentially a single-pole transfer function.
The pole frequency of the transfer function is determined by
the dc-to-dc converter’s output capacitance, input and output
voltage, and output load. The AD5757 uses an external capaci-
tor in conjunction with an internal 150 k resistor to compensate
the regulator loop. Alternatively, an external compensation
resistor can be used in series with the compensation capacitor
by setting the DC-DC Comp bit in the dc-to-dc control register.
In this case, a ~50 k resistor is recommended. A description
of the advantages of this can be found in the AICC Supply
Requirements—Slewing section. For typical applications, a
10 nF dc-to-dc compensation capacitor is recommended.
DC-to-DC Converter Input and Output Capacitor
Selection
The output capacitor affects ripple voltage of the dc-to-dc con-
verter and indirectly limits the maximum slew rate at which the
channel output current can rise. The ripple voltage is caused by
a combination of the capacitance and equivalent series resistance
(ESR) of the capacitor. For the AD5757, a ceramic capacitor
of 4.7 F is recommended for typical applications. Larger
capacitors or paralleled capacitors improve the ripple at the
expense of reduced slew rate. Larger capacitors also impact
the AVCC supplies current requirements while slewing (see the
AICC Supply Requirements—Slewing section). This capacitance
at the output of the dc-to-dc converter should be >3 F under
all operating conditions.
The input capacitor provides much of the dynamic current
required for the dc-to-dc converter and should be a low ESR
component. For the AD5757, a low ESR tantalum or ceramic
capacitor of 10 F is recommended for typical applications.
Ceramic capacitors must be chosen carefully because they can
exhibit a large sensitivity to dc bias voltages and temperature.
X5R or X7R dielectrics are preferred because these capacitors
remain stable over wider operating voltage and temperature
ranges. Care must be taken if selecting a tantalum capacitor to
ensure a low ESR value.
AICC SUPPLY REQUIREMENTS—STATIC
The dc-to-dc converter is designed to supply a VBOOST_x voltage of
VBOOST = IOUT × RLOAD + Headroom
(2)
See Figure 31 for a plot of headroom supplied vs. output
voltage. This means that, for a fixed load and output voltage,
the dc-to-dc converter output current can be calculated by
the following formula:
CC
V
BOOST
OUT
CC
AV
V
I
AV
Efficiency
Out
Power
AI
BOOST
×
=
×
=
η
(3)
where:
IOUT is the output current from IOUT_x in amps.
ηV
BOOST
and Figure 34).
AICC SUPPLY REQUIREMENTS—SLEWING
The AICC current requirement while slewing is greater than in
static operation because the output power increases to charge
the output capacitance of the dc-to-dc converter. This transient
current can be quite large (see Figure 58), although the methods
described in the Reducing AICC Current Requirements section
can reduce the requirements on the AVCC supply. If not enough
AICC current can be provided, the AVCC voltage drops. Due to
this AVCCdrop, the AICC current required to slew increases
further. This means that the voltage at AVCC drops further (see
Equation 3) and the VBOOST_x voltage, and thus the output volt-
age, may never reach its intended value. Because this AVCC
voltage is common to all channels, this may also affect other
channels.
0
5
10
15
20
25
30
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0
0.5
1.0
1.5
2.0
2.5
I O
UT
_
x
CURRE
NT
(
mA
)/
V
B
OOS
T
_
x
VO
LT
A
G
E
(V)
AI
CC
CURRE
NT
(
A)
TIME (ms)
AICC
IOUT
VBOOST
0mA TO 24mA RANGE
1k LOAD
fSW = 410kHz
INDUCTOR = 10H (XAL4040-103)
TA = 25°C
09225-
184
Figure 58. AICC Current vs. Time for 24 mA Step Through 1 k Load
with Internal Compensation Resistor
Reducing AICC Current Requirements
There are two main methods that can be used to reduce the
AICC current requirements. One method is to add an external
compensation resistor, and the other is to use slew rate control.
Both of these methods can be used in conjunction.
A compensation resistor can be placed at the COMPDCDC_x pin
in series with the 10 nF compensation capacitor. A 51 k external
compensation resistor is recommended. This compensation
increases the slew time of the current output but eases the AICC
transient current requirements. Figure 59 shows a plot of AICC
current for a 24 mA step through a 1 k load when using a
51 k compensation resistor. This method eases the current
requirements through smaller loads even further, as shown in
相关PDF资料 |
PDF描述 |
|---|---|
| EVAL-AD5760SDZ | BOARD EVAL FOR AD5760SDZ |
| HKQ0603S4N7C-T | INDUCTOR HI FREQ 4.7NH 0201 |
| LGU2D471MELZ | CAP ALUM 470UF 200V 20% SNAP |
| SEK331M100ST | CAP ALUM 330UF 100V 20% RADIAL |
| MC56F8006DEMO | DEMO BOARD FOR MC56F8006 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD5760SDZ | 功能描述:BOARD EVAL FOR AD5760SDZ RoHS:否 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5764EB | 制造商:Analog Devices 功能描述:EVALUATION BOARD FOR QUAD, 16-BIT, HIGH ACCURACY, SERIAL INPUT, BIPOLAR VOLTAGE OUTPUT DAC 制造商:Analog Devices 功能描述:EVALUATION CONTROL BOARD I.C. - Bulk |
| EVAL-AD5764EBZ | 功能描述:BOARD EVAL FOR AD5764 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5764REBZ | 功能描述:EVAL BOARD FOR AD5764 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5765EBZ | 功能描述:BOARD EVAL FOR AD5765 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
发布紧急采购，3分钟左右您将得到回复。