参数资料
型号: EVAL-AD7328SDZ
厂商: Analog Devices Inc
文件页数: 7/37页
文件大小: 0K
描述: BOARD EVAL FOR AD7328
标准包装: 1
系列: iCMOS®
ADC 的数量: 1
位数: 12
采样率(每秒): 1M
数据接口: DSP,MICROWIRE?,QSPI?,串行,SPI?
输入范围: ±10 V
在以下条件下的电源(标准): 31mW @ 1MSPS
工作温度: -40°C ~ 85°C
已用 IC / 零件: AD7328
已供物品:
AD7328
Data Sheet
Rev. C | Page 14 of 36
Channel-to-Channel Isolation
Channel-to-channel isolation is a measure of the level of crosstalk
between any two channels. It is measured by applying a full-scale,
100 kHz sine wave signal to all unselected input channels and
determining the degree to which the signal attenuates in the
selected channel with a 50 kHz signal. Figure 14 shows the worst
case across all eight channels for the AD7328. The analog input
range is programmed to be the same on all channels.
Intermodulation Distortion
With inputs consisting of sine waves at two frequencies, fa and fb,
any active device with nonlinearities creates distortion products
at sum and difference frequencies of mfa ± nfb, where m, n = 0,
1, 2, 3, and so on. Intermodulation distortion terms are those
for which neither m nor n are equal to 0. For example, the
second-order terms include (fa + fb) and (fa fb), whereas the
third-order terms include (2fa + fb), (2fa fb), (fa + 2fb), and
(fa 2fb).
The AD7328 is tested using the CCIF standard where two input
frequencies near the top end of the input bandwidth are used.
In this case, the second-order terms are usually distanced in
frequency from the original sine waves, whereas the third-order
terms are usually at a frequency close to the input frequencies.
As a result, the second- and third-order terms are specified
separately. The calculation of the intermodulation distortion is
per the THD specification, where it is the ratio of the rms sum
of the individual distortion products to the rms amplitude of
the sum of the fundamentals expressed in decibels.
Power Supply Rejection (PSR)
Variations in power supply affect the full-scale transition but not
the linearity of the converter. Power supply rejection is the
maximum change in the full-scale transition point due to a
change in power supply voltage from the nominal value (see the
Thermal Hysteresis
Thermal hysteresis is defined as the absolute maximum change
of reference output voltage after the device is cycled through
temperature from either
T_HYS+ = +25°C to TMAX to +25°C
or
T_HYS = +25°C to TMIN to +25°C
It is expressed in ppm using the following equation:
6
10
)
C
25
(
)
_
(
)
C
25
(
)
ppm
(
×
°
°
=
REF
HYS
V
HYS
T
V
where:
VREF(25°C) is VREF at 25°C.
VREF(T_HYS) is the maximum change of VREF at T_HYS+ or
T_HYS.
Common-Mode Rejection Ratio (CMRR)
CMRR is defined as the ratio of the power in the ADC output
at full-scale frequency, f, to the power of a 100 mV sine wave
applied to the common-mode voltage of the VIN+ and VIN
frequency, fS, as
CMRR (dB) = 10 log (Pf/PfS)
where Pf is the power at frequency f in the ADC output, and PfS
is the power at frequency fS in the ADC output (see Figure 17).
相关PDF资料
PDF描述
ESC06DRTH-S734 CONN EDGECARD 12POS DIP .100 SLD
ECC31DCAI CONN EDGECARD 62POS R/A .100 SLD
EVAL-AD7276SDZ BOARD EVAL FOR AD7276
ABC05DRYS CONN EDGECARD 10POS .100 DIP SLD
ESC06DREI-S734 CONN EDGECARD 12POS .100 EYELET
相关代理商/技术参数
参数描述
EVAL-AD7329CB 制造商:Analog Devices 功能描述:
EVAL-AD7329CBZ 功能描述:BOARD EVALUATION FOR AD7329CBZ RoHS:是 类别:编程器,开发系统 >> 评估板 - 模数转换器 (ADC) 系列:iCMOS® 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率(每秒):94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源(标准):- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板,软件
EVAL-AD73311EB 制造商:AD 制造商全称:Analog Devices 功能描述:Low Cost, Low Power CMOS General Purpose Analog Front End
EVAL-AD73311EZ 制造商:AD 制造商全称:Analog Devices 功能描述:Low Cost, Low Power CMOS General Purpose Analog Front End
EVAL-AD73311LEB 制造商:AD 制造商全称:Analog Devices 功能描述:Low Cost, Low Power CMOS General Purpose Analog Front End