- 您现在的位置：买卖IC网 > PDF目录17053 > EVAL-AD7476ACBZ (Analog Devices Inc)BOARD EVALUATION FOR AD7476A PDF资料下载
参数资料
| 型号： | EVAL-AD7476ACBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 7/29页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR AD7476A |
| 标准包装： | 1 |
| ADC 的数量： | 1 |
| 位数： | 12 |
| 采样率（每秒）： | 1M |
| 数据接口： | 串行 |
| 输入范围： | 0 ~ 5.25 V |
| 在以下条件下的电源（标准）： | 17.5mW @ 1MSPS，5 V |
| 工作温度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7476A |
| 已供物品： | 板，CD |
| 相关产品： | AD7476ARTZ-500RL7DKR-ND - IC ADC 12BIT 1MSPS SOT-23-6 AD7476ABKSZREELDKR-ND - IC ADC 12BIT 1MSPS SC70-6 AD7476BRTZ-R2TR-ND - IC ADC 12BIT 1MSPS SOT23-6 AD7476ARTZ-REEL7-ND - IC ADC 12BIT 1MSPS LP SOT23-6 AD7476ABKSZ-500RL7-ND - IC ADC 12BIT 1MSPS LP SC70-6 AD7476AAKSZ-REEL7-ND - IC ADC 12BIT 1MSPS LP SC70-6 AD7476AAKSZ-500RL7TR-ND - IC ADC 12BIT 1MSPS LP SC70-6 AD7476AYRMZ-REEL7-ND - IC ADC 12BIT 1MSPS LP 8MSOP AD7476AAKSZ-REEL-ND - IC ADC 12BIT 1MSPS LP SC70-6 AD7476ARTZ-500RL7CT-ND - IC ADC 12BIT 1MSPS SOT-23-6 更多... |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
AD7476A/AD7477A/AD7478A
Rev. F | Page 14 of 28
TERMINOLOGY
Integral Nonlinearity (INL)
INL is the maximum deviation from a straight line passing
through the endpoints of the ADC transfer function. For the
AD7476A/AD7477A/AD7478A, the endpoints of the transfer
function are zero scale (1 LSB below the first code transition),
and full scale (1 LSB above the last code transition).
Differential Nonlinearity (DNL)
DNL is the difference between the measured and the ideal
1 LSB change between any two adjacent codes in the ADC.
Offset Error
This is the deviation of the first code transition (00 . . . 000) to
(00 . . . 001) from the ideal, that is, AGND + 1 LSB.
Gain Error
This is the deviation of the last code transition (111 . . . 110) to
(111 . . . 111) from the ideal, that is, VREF – 1 LSB after the offset
error has been adjusted out.
Track-and-Hold Acquisition Time
The track-and-hold amplifier returns to track mode at the end
of a conversion. The track-and-hold acquisition time is the time
required for the output of the track-and-hold amplifier to reach
its final value, within 0.5 LSB, after the end of conversion. See
the Serial Interface section for more details.
Signal-to-(Noise + Distortion) Ratio (SINAD)
This is the measured ratio of signal-to-(noise + distortion) at
the output of the ADC. The signal is the rms amplitude of the
fundamental. Noise is the sum of all nonfundamental signals up
to half the sampling frequency (fS/2), excluding dc. The ratio is
dependent on the number of quantization levels in the digitiza-
tion process; the more levels, the smaller the quantization noise.
The theoretical signal-to-(noise + distortion) ratio for an ideal
N-bit converter with a sine wave input is given by signal-to-
(noise + distortion) = (6.02 N + 1.76) dB. Thus, it is 74 dB for a
12-bit converter, 62 dB for a 10-bit converter, and 50 dB for an
8-bit converter.
Total Unadjusted Error (TUE)
This is a comprehensive specification that includes the gain,
linearity, and offset errors.
Total Harmonic Distortion (THD)
Total harmonic distortion is the ratio of the rms sum of
harmonics to the fundamental. It is defined as
1
2
6
2
5
2
4
2
3
2
V
THD
+
= log
20
)
dB
(
where V1 is the rms amplitude of the fundamental, and V2, V3,
V4, V5, and V6 are the rms amplitudes of the second through the
sixth harmonics.
Peak Harmonic or Spurious Noise (SFDR)
Peak harmonic or spurious noise is defined as the ratio of the rms
value of the next largest component in the ADC output spectrum
(up to fS/2 and excluding dc) to the rms value of the fundamental.
Normally, the value of this specification is determined by the largest
harmonic in the spectrum. For ADCs where the harmonics are
buried in the noise floor, it is a noise peak.
Intermodulation Distortion (IMD)
With inputs consisting of sine waves at two frequencies, fa and
fb, any active device with nonlinearities create distortion
products at sum and difference frequencies of mfa, nfb, where
m and n = 0, 1, 2, 3, and so on. Intermodulation distortion
terms are those for which neither m nor n are equal to zero. For
example, the second-order terms include (fa + fb) and (fa – fb),
and the third-order terms include (2fa + fb), (2fa – fb), (fa + 2fb),
and (fa – 2fb).
The AD7476A/AD7477A/AD7478A are tested using the CCIF
standard where two input frequencies are used (see fa and fb in
the Specifications section). In this case, the second-order terms
are usually distanced in frequency from the original sine waves,
while the third-order terms are usually at a frequency close to the
input frequencies. As a result, the second- and third-order terms
are specified separately. The calculation of the intermodulation
distortion is per the THD specification, where it is the ratio of
the rms sum of the individual distortion products to the rms
amplitude of the sum of the fundamentals expressed in decibels.
相关PDF资料 |
PDF描述 |
|---|---|
| 0210490923 | CABLE JUMPER 1.25MM .051M 23POS |
| EVAL-AD7450CBZ | BOARD EVALUATION FOR AD7450 |
| VI-B2R-EY | CONVERTER MOD DC/DC 7.5V 50W |
| VI-B1B-EY | CONVERTER MOD DC/DC 95V 50W |
| 0210490922 | CABLE JUMPER 1.25MM .051M 23POS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD7476CB | 制造商:Analog Devices 功能描述:Evaluation Board For AD7476 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk |
| EVAL-AD7476CBZ | 功能描述:BOARD EVAL FOR AD7476 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7477ACB | 制造商:Analog Devices 功能描述:EVAL BD FOR AD7477A 12-/10-/8BIT ADCS IN 6-LEAD SC70 - Bulk |
| EVAL-AD7477ACB4 | 制造商:AD 制造商全称:Analog Devices 功能描述:2.35 V to 5.25 V, 1 MSPS, 12-/10-/8-Bit ADCs in 6-Lead SC70 |
| EVAL-AD7477CB | 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk |
发布紧急采购，3分钟左右您将得到回复。