- 您现在的位置：买卖IC网 > PDF目录17031 > EVAL-AD7641CBZ (Analog Devices Inc)BOARD EVALUATION FOR AD7641 PDF资料下载
参数资料
| 型号： | EVAL-AD7641CBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 11/28页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR AD7641 |
| 产品培训模块： | ADC Applications ADC Architectures ADC DC/AC Performance |
| 标准包装： | 1 |
| 系列： | PulSAR® |
| ADC 的数量： | 1 |
| 位数： | 18 |
| 采样率（每秒）： | 2M |
| 数据接口： | 串行 |
| 输入范围： | ±2.5 V |
| 在以下条件下的电源（标准）： | 2MSPS 带内部基准时为 75mW |
| 工作温度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7641 |
| 已供物品： | 板 |
| 相关产品： | AD7641BSTZRL-ND - IC ADC 18BIT 2MSPS SAR 48-LQFP AD7641BCPZRL-ND - IC ADC 18BIT 2MSPS SAR 48-LFCSP AD7641BSTZ-ND - IC ADC 18BIT 2MSPS SAR 48-LQFP AD7641BCPZ-ND - IC ADC 18BIT 2MSPS SAR 48-LFCSP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD7641
Rev. 0 | Page 19 of 28
However, because the AD7641 has a fine lead pitch, guarding
this node is not practical. Therefore, in these industrial and
other types of applications, it is recommended to use a conformal
coating, such as Dow Corning 1-2577 or HumiSeal 1B73.
For applications that use multiple AD7641 devices, it is more
effective to use an external reference with the internal reference
buffer to buffer the reference voltage. However, because the
reference buffers are not unity gain, ratiometric, simultaneously
sampled designs should use an external reference and external
buffer, such as the
External 1.2 V Reference and Internal Buffer (PDBUF =
Low, PDREF = High)
same reference level for all converters.
To use an external reference along with the internal buffer,
PDREF should be high and PDBUF should be low. This powers
down the internal reference and allows the 1.2 V reference to
be applied to REFBUFIN, producing 2.048 V (typically) on
the REF pin.
The voltage reference temperature coefficient (TC) directly
impacts full scale; therefore, in applications where full-scale
accuracy matters, care must be taken with the TC. For instance,
a ±4 ppm/°C TC of the reference changes full scale by ±1 LSB/°C.
External 2.5 V Reference (PDBUF = High, PDREF = High)
Note that VREF can be increased to AVDD + 0.1 V. Because the
input range is defined in terms of VREF, this would essentially
increase the range to 0 V to 2.8 V with an AVDD = 2.7 V.
To use an external 2.5 V reference directly on the REF pin,
PDREF and PDBUF should both be high.
For improved drift performance, an external reference, such as
the
Temperature Sensor
using the external voltage reference are:
The TEMP pin measures the temperature of the AD7641. To
improve the calibration accuracy over the temperature range,
the output of the TEMP pin is applied to one of the inputs of
the analog switch (such as,
The SNR and dynamic range improvement (about 1.7 dB)
resulting from the use of a reference voltage very close to
the supply (2.5 V) instead of a typical 2.048 V reference
when the internal reference is used. This is calculated by
ADG779), and the ADC itself is
used to measure its own temperature. This configuration is
shown in Figure 27.
=
50
.
2
048
.
2
log
20
SNR
04
76
1-
02
8
ADG779
AD8021
CC
ANALOG INPUT
(UNIPOLAR)
AD7641
IN+
TEMPERATURE
SENSOR
TEMP
The power savings when the internal reference is powered
down (PDREF high).
PDREF and PDBUF power down the internal reference and
the internal reference buffer, respectively. The input current
of PDREF and PDBUF should never exceed 20 mA. This can
occur when the driving voltage is above AVDD (for instance, at
power-up). In this case, a 125 Ω series resistor is recommended.
Figure 27. Use of the Temperature Sensor
Reference Decoupling
Whether using an internal or external reference, the AD7641
voltage reference input (REF) has a dynamic input impedance;
therefore, it should be driven by a low impedance source with
efficient decoupling between the REF and REFGND inputs.
This decoupling depends on the choice of the voltage reference
but usually consists of a low ESR capacitor connected to REF
and REFGND with minimum parasitic inductance. A 10 μF
(X5R, 1206 size) ceramic chip capacitor (or 47 μF tantalum
capacitor) is appropriate when using either the internal
reference or one of the recommended reference voltages.
The placement of the reference decoupling is also important to
the performance of the AD7641. The decoupling capacitor
should be mounted on the same side as the ADC right at the
REF pin with a thick PCB trace. The REFGND should also connect
to the reference decoupling capacitor with the shortest distance.
相关PDF资料 |
PDF描述 |
|---|---|
| DC1571A-B | BOARD SAR ADC LTC2382-16 |
| DC1571A-A | BOARD SAR ADC LTC2383-16 |
| STD17W-5 | WIRE & CABLE MARKERS |
| STD17W-T | WIRE & CABLE MARKERS |
| EVAL-AD7612CBZ | BOARD EVALUATION FOR AD7612 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD7641EDZ | 功能描述:BOARD EVAL FOR AD7641 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7643CB | 制造商:Analog Devices 功能描述:EVAL BD FOR AD7643 - Bulk |
| EVAL-AD7643CBZ | 功能描述:BOARD EVALUATION FOR AD7643 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:PulSAR® 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7643EDZ | 功能描述:BOARD EVAL FOR AD7643 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7650CB | 制造商:Analog Devices 功能描述:EVAL BD EVAL BD AD765X/AD766X/AD767X - Bulk |
发布紧急采购，3分钟左右您将得到回复。