- 您现在的位置：买卖IC网 > PDF目录17032 > EVAL-AD7674CBZ (Analog Devices Inc)BOARD EVALUATION FOR AD7674 PDF资料下载
参数资料
| 型号： | EVAL-AD7674CBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 2/28页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR AD7674 |
| 产品培训模块： | ADC Applications ADC Architectures ADC DC/AC Performance |
| 标准包装： | 1 |
| 系列： | PulSAR® |
| ADC 的数量： | 1 |
| 位数： | 18 |
| 采样率（每秒）： | 800k |
| 数据接口： | 串行，并联 |
| 输入范围： | 0 ~ 5 V |
| 在以下条件下的电源（标准）： | 126mW @ 800kSPS |
| 工作温度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7674 |
| 已供物品： | 板 |
| 相关产品： | AD7674ACPZ-ND - IC ADC 18BIT SAR 5V 48LFCSP AD7674ACPZRL-ND - IC ADC 18BIT SAR 5V 48LFCSP AD7674ASTZ-ND - IC ADC 18BIT 800KSPS 48-LQFP AD7674ASTZRL-ND - IC ADC 18BIT 800KSPS 48-LQFP T/R |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD7674
Rev. A | Page 10 of 28
Pin No.
Mnemonic
Type1
Description
29
BUSY
DO
Busy Output. Transitions HIGH when a conversion is started. Remains HIGH until the conversion is
complete and the data is latched into the on-chip shift register. The falling edge of BUSY could be used
as a data ready clock signal.
30
DGND
P
Must Be Tied to Digital Ground.
31
RD
DI
Read Data. When CS and RD are both LOW, the interface parallel or serial output bus is enabled.
32
CS
DI
Chip Select. When CS and RD are both LOW, the interface parallel or serial output bus is enabled. CS is
also used to gate the external clock.
33
RESET
DI
Reset Input. When set to a logic HIGH, reset the AD7674. Current conversion, if any, is aborted. If not
used, this pin could be tied to DGND.
34
PD
DI
Power-Down Input. When set to a logic HIGH, power consumption is reduced and conversions are
inhibited after the current one is completed.
35
CNVST
DI
Start Conversion. A falling edge on CNVST puts the internal sample/hold into the hold state and initiates
a conversion. In Impulse mode (IMPULSE HIGH, WARP LOW), if CNVST is held LOW when the acquisition
phase (t8) is complete, the internal sample/hold is put into hold and a conversion is immediately started.
36
AGND
P
Must Be Tied to Analog Ground.
37
REF
AI
Reference Input Voltage and Internal Reference Buffer Output. Apply an external reference on REF if the
internal reference buffer is not used. Should be decoupled effectively with or without the internal buffer.
38
REFGND
AI
Reference Input Analog Ground.
39
IN–
AI
Differential Negative Analog Input.
40–42,
45
NC
No Connect.
43
IN+
AI
Differential Positive Analog Input.
46
REFBUFIN
AI
Reference Buffer Input Voltage. The internal reference buffer has a fixed gain. It outputs 4.096 V typically
when 2.5 V is applied on this pin.
48
PDBUF
DI
Allows Choice of Buffering Reference. When LOW, buffer is selected. When HIGH, buffer is switched off.
49
(EPAD)
Exposed Pad
The exposed pad is internally connected to AGND. This connection is not required to meet the electrical
performances however, for increased reliability of the solder joints, it is recommended that the pad be
soldered to the analog ground of the system.
1AI = Analog Input; DI = Digital Input; DI/O = Bidirectional Digital; DO = Digital Output; P = Power.
Table 7. Data Bus Interface Definitions
MODE
MODE1
MODE0
D0/OB/2C
D1/A0
D2/A1
D[3]
D[4:9]
D[10:11]
D[12:15]
D[16:17]
Description
0
R[0]
R[1]
R[2]
R[3]
R[4:9]
R[10:11]
R[12:15]
R[16:17]
18-Bit Parallel
1
0
1
OB/2C
A0:0
R[2]
R[3]
R[4:9]
R[10:11]
R[12:15]
R[16:17]
16-Bit High Word
1
0
1
OB/2C
A0:1
R[0]
R[1]
All Zeros
16-Bit Low Word
2
1
0
OB/2C
A0:0
A1:0
All Hi-Z
R[10:11]
R[12:15]
R[16:17]
8-Bit HIGH Byte
2
1
0
OB/2C
A0:0
A1:1
All Hi-Z
R[2:3]
R[4:7]
R[8:9]
8-Bit MID Byte
2
1
0
OB/2C
A0:1
A1:0
All Hi-Z
R[0:1]
All Zeros
8-Bit LOW Byte
2
1
0
OB/2C
A0:1
A1:1
All Hi-Z
All Zeros
R[0:1]
8-Bit LOW Byte
3
1
OB/2C
All Hi-Z
Serial Interface
R[0:17] is the 18-bit ADC value stored in its output register.
相关PDF资料 |
PDF描述 |
|---|---|
| GEM31DCAD | CONN EDGECARD 62POS R/A .156 SLD |
| GCM25DCAD | CONN EDGECARD 50POS R/A .156 SLD |
| MIC2019A-1YM6 TR | IC POWER SWITCH 1.0A SOT23-6 |
| CB2012T1R0M | INDUCTOR POWER 1.0UH 900MA 0805 |
| ADR430ARZ-REEL7 | IC VREF SERIES PREC 2.048V 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD7674EDZ | 功能描述:BOARD EVAL FOR AD7674 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7675CB | 制造商:AD 制造商全称:Analog Devices 功能描述:Evaluation Board AD766X/AD767X |
| EVAL-AD7675CBZ | 功能描述:BOARD EVALUATION FOR AD7675 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:PulSAR® 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7676CB | 制造商:AD 制造商全称:Analog Devices 功能描述:Evaluation Board AD766X/AD767X |
| EVAL-AD7676CBZ | 功能描述:BOARD EVALUATION FOR AD7676 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:PulSAR® 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
发布紧急采购，3分钟左右您将得到回复。