- 您现在的位置：买卖IC网 > PDF目录17044 > EVAL-AD7685SDZ (Analog Devices Inc)BOARD EVAL FOR AD7685 PDF资料下载
参数资料
| 型号： | EVAL-AD7685SDZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 14/28页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD7685 |
| 标准包装： | 1 |
| 系列： | PulSAR® |
| ADC 的数量： | 1 |
| 位数： | 16 |
| 采样率（每秒）： | 250k |
| 数据接口： | 串行 |
| 输入范围： | ±VREF |
| 在以下条件下的电源（标准）： | 10mW @ 250kSPS |
| 工作温度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7685 |
| 已供物品： | 板 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD7685
Rev. C | Page 21 of 28
CS MODE 4-WIRE WITH BUSY INDICATOR
This mode is usually used when a single AD7685 is connected
to an SPI-compatible digital host, which has an interrupt input,
and it is desired to keep CNV, which is used to sample the
analog input, independent of the signal used to select the data
reading. This requirement is particularly important in
applications where low jitter on CNV is desired.
The connection diagram is shown in Figure 40, and the
corresponding timing is given in Figure 41.
With SDI high, a rising edge on CNV initiates a conversion,
selects the CS mode, and forces SDO to high impedance. In this
mode, CNV must be held high during the conversion phase and
the subsequent data readback (if SDI and CNV are low, SDO is
driven low). Prior to the minimum conversion time, SDI could
be used to select other SPI devices, such as analog multiplexers,
but SDI must be returned low before the minimum conversion
time and held low until the maximum conversion time to
guarantee the generation of the BUSY signal indicator. When
the conversion is complete, SDO goes from high impedance to
low. With a pull-up on the SDO line, this transition can be used
as an interrupt signal to initiate the data readback controlled by
the digital host. The AD7685 then enters the acquisition phase
and powers down. The data bits are then clocked out, MSB first,
by subsequent SCK falling edges. The data is valid on both SCK
edges. Although the rising edge can be used to capture the data,
a digital host using the SCK falling edge will allow a faster
reading rate provided it has an acceptable hold time. After the
optional 17th SCK falling edge, or SDI going high, whichever is
earlier, the SDO returns to high impedance.
DATA IN
IRQ
CLK
CONVERT
CS1
VIO
DIGITAL HOST
02
96
8-
03
8
47k
CNV
SCK
SDO
SDI
AD7685
Figure 40. CS Mode 4-Wire with BUSY Indicator Connection Diagram
SDO
D15
D14
D1
D0
tDIS
SCK
1
2
3
151617
tSCK
tSCKL
tSCKH
tHSDO
tDSDO
tEN
CONVERSION
ACQUISITION
tCONV
tCYC
tACQ
ACQUISITION
SDI
CNV
tSSDICNV
tHSDICNV
02
96
8-
0
39
Figure 41. CS Mode 4-Wire with BUSY Indicator Serial Interface Timing
相关PDF资料 |
PDF描述 |
|---|---|
| ADR421ARZ-REEL7 | IC VREF SERIES PREC 2.5V 8-SOIC |
| REC5-483.3SRW/H6/C | CONV DC/DC 5W 36-72VIN 3.3VOUT |
| 0982660899 | CBL 21PS 0.5MM JMPR TYPE A 1.18" |
| PH50S280-15 | DC-DC CONVERTER 50W 15V OUTPUT |
| UPS2F221MRD | CAP ALUM 220UF 315V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD7686CB | 制造商:Analog Devices 功能描述: |
| EVAL-AD7686CBZ | 功能描述:BOARD EVALUATION FOR AD7686 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:PulSAR® 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7686SDZ | 功能描述:数据转换 IC 开发工具 EVAL BOARD 100Ksps/400Ksps 16 bit I.C RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| EVAL-AD7687CB | 制造商:Analog Devices 功能描述:EVAL BOARD 16-BIT, 250KSPS DIFFER . I.C. - Bulk |
| EVAL-AD7687CBZ | 功能描述:BOARD EVALUATION FOR AD7687 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:PulSAR® 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
发布紧急采购，3分钟左右您将得到回复。