- 您现在的位置：买卖IC网 > PDF目录17044 > EVAL-AD7688SDZ (Analog Devices Inc)BOARD EVAL FOR AD7688 PDF资料下载
参数资料
| 型号： | EVAL-AD7688SDZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 16/28页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD7688 |
| 标准包装： | 1 |
| 系列： | PulSAR® |
| ADC 的数量： | 1 |
| 位数： | 16 |
| 采样率（每秒）： | 500k |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 输入范围： | ±VREF |
| 在以下条件下的电源（标准）： | 3.75mW @ 100kSPS |
| 工作温度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7688 |
| 已供物品： | 板 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD7688
Rev. A | Page 23 of 28
APPLICATION HINTS
LAYOUT
The printed circuit board that houses the AD7688 should be
designed so that the analog and digital sections are separated
and confined to certain areas of the board. The pinout of the
AD7688, with all its analog signals on the left side and all its
digital signals on the right side, eases this task.
Avoid running digital lines under the device because these
couple noise onto the die, unless a ground plane under the
AD7688 is used as a shield. Fast switching signals, such as CNV
or clocks, should never run near analog signal paths. Crossover
of digital and analog signals should be avoided
At least one ground plane should be used. It could be common
or split between the digital and analog sections. In the latter
case, the planes should be joined underneath the AD7688s.
The AD7688 voltage reference input REF has a dynamic input
impedance and should be decoupled with minimal parasitic
inductances. This is done by placing the reference decoupling
ceramic capacitor close to, and ideally right up against, the REF
and GND pins and connecting it with wide, low impedance
traces.
Finally, the power supplies VDD and VIO of the AD7688
should be decoupled with ceramic capacitors (typically 100 nF)
placed close to the AD7688 and connected using short and wide
traces to provide low impedance paths and reduce the effect of
glitches on the power supply lines.
An example of layout following these rules is shown in
EVALUATING THE AD7688’S PERFORMANCE
Other recommended layouts for the AD7688 are outlined
in the documentation of the evaluation board for the AD7688
(EVAL-AD7688). The evaluation board package includes
a fully assembled and tested evaluation board, documentation,
and software for controlling the board from a PC via the
EVAL-CONTROL BRD3.
02973-045
Figure 46. Example of Layout of the AD7688 (Top Layer)
02973-046
Figure 47. Example of Layout of the AD7688 (Bottom Layer)
相关PDF资料 |
PDF描述 |
|---|---|
| SDR0805-680KL | INDUCTOR UNSHIELD 68UH .85A SMD |
| MIC2076A-2YM | IC SW DISTRIBUTION 2CH 8SOIC |
| GEM25DTBH | CONN EDGECARD 50POS R/A .156 SLD |
| PH50S245 | CONVERTER DC/DC 5V 50W 6-PIN |
| 94SVP687X0004F8 | CAP ALUM 680UF 4V 20% SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD7689CBZ | 制造商:Analog Devices 功能描述:EVAL BOARD 8 CH 250KSPS 16BIT ADC IC - Bulk |
| EVAL-AD7689EDZ | 功能描述:BOARD EVAL AD7689 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:PulSAR® 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7689EDZ | 制造商:Analog Devices 功能描述:16 Bit A/D Converter Eval. Board |
| EVAL-AD7690CB | 制造商:Analog Devices 功能描述:AD7690 EVAL - Bulk |
| EVAL-AD7690SDZ | 功能描述:BOARD EVAL FOR AD7690 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:PulSAR® 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
发布紧急采购，3分钟左右您将得到回复。