- 您现在的位置：买卖IC网 > PDF目录16623 > EVAL-ADM1186-1MBZ (Analog Devices Inc)KIT MICRO EVALUATION ADM1186-1 PDF资料下载
参数资料
| 型号： | EVAL-ADM1186-1MBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 16/28页 |
| 文件大小： | 0K |
| 描述： | KIT MICRO EVALUATION ADM1186-1 |
| 标准包装： | 1 |
| 主要目的： | 电源管理，电源监控器/跟踪器/序列发生器 |
| 已用 IC / 零件： | ADM1186-1 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
1 . 4 × ( R1 + R2 ) 1 . 4 × ( 11 k + 10 k )
V MID = =
ADM1186
SEQUENCE CONTROL USING A SUPPLY RAIL
The UP and DOWN inputs on the ADM1186-1 and the
UP/DOWN input on the ADM1186-2 are used to initiate
power-up and power-down sequences. These inputs are
designed for use with digital or analog signals, such as power
supply rails. Using a power supply rail to control the up and
down sequencing allows the ADM1186 to perform sequencing
and monitoring functions for five supply rails.
When using a supply rail to control an ADM1186-1 (with
the UP and DOWN pins connected) or an ADM1186-2,
some hysteresis is required. The hysteresis is added on the
joined UP and DOWN pins of the ADM1186-1 or on the
UP/DOWN pin of the ADM1186-2 to ensure that a slowly
ramping supply rail does not cause spurious rising or falling
edges that would otherwise cause state machine faults.
To provide the necessary hysteresis, a single additional resistor
(RH in Figure 27) is connected between the joined UP and
DOWN pins of the ADM1186-1 and the OUT1 pin of the
device, or between the UP/DOWN pin of the ADM1186-2 and
the OUT1 pin of the device.
Data Sheet
In the example application shown in Figure 27, the following
values could be used:
RP = 10 kΩ
VP = 5 V
VIN = 3.3 V
The values of the R1 and R2 resistors determine the midpoint
of the hysteresis, V MID , about which V H and V L set the levels at
which power-up and power-down sequences are initiated. For a
3.3 V supply, a threshold just below 3 V could be used, making
R1 = 11 kΩ and R2 = 10 kΩ and giving a midpoint of 2.94 V.
R2 10 k
V MID = 2.94 V
As a general rule, the value for RH is approximately 60 times
the value of R1 in parallel with R2. In this example, R1 in
parallel with R2 is 5.24 kΩ, so RH would be approximately
314 kΩ. Taking a value of 300 kΩ for RH and using this value
in the previous equations for V H , V L , and V SHYS , the following
values are obtained:
V H = 1 . 4 × ? 1 + ? 11 k ×
10 k + 300 k ? ?
10 k × 300 k ? ??
VIN
RH
3.3V
VP
? ?
? ?
?
? 1 . 4
V L = 1 . 4 + ? 11 k × ?
? 10 k
? ?
R1
R2
ADM1186-1
UP
VCC
STATE
OUT1
RP
V H = 2.991 V
?
?
? ?
?
5 ? 1 . 4 ? ?
300 k + 10 k ? ? ? ?
DOWN
MACHINE
V L = 2.812 V
V SHYS = ( 2 . 991 ? 2 . 812 ) × ?
? 10 k ?
? 11 k + 10 k ?
1.4V
Figure 27. Using a Supply Rail to Control Sequencing with Hysteresis
When OUT1 is low, the resistor RH sinks current from the
node at the midpoint of R1 and R2, slightly increasing the VIN
voltage needed to start a power-up sequence, referred to as V H .
When OUT1 is high, RH sources current into the midpoint of
R1 and R2, decreasing the VIN voltage necessary to start a
power-down sequence, referred to as V L .
The hysteresis at the VIN node is simply V H ? V L . As the R1
and R2 resistors scale VIN down, the hysteresis on VIN is also
scaled down. The scaled hysteresis, V SHYS , at the inputs to the
UP and DOWN pins (ADM1186-1) or the UP/DOWN pin
(ADM1186-2) must be at least 75 mV. The value of RH is
selected to ensure that this is the case.
?
V SHYS = 0.085 V
Because the value of V SHYS is greater than the 75 mV of scaled
hysteresis required, the RH resistor value selected is sufficient.
If the value of V SHYS obtained is too small, the value of RH can
be reduced, increasing the scaled hysteresis provided.
V H = 1 . 4 × ? 1 + ? ? R1 ×
R2 + RH ? ?
R2 × RH ? ??
?
? ?
?
? 1 . 4
V L = 1 . 4 + ? R1 × ?
? R2
?
?
? ?
?
? ?
VP ? 1 . 4 ? ?
RH + RP ? ? ? ?
V SHYS = ( V H ? V L ) × ? ?
R2 ?
? R1 + R2 ?
?
Rev. B | Page 16 of 28
相关PDF资料 |
PDF描述 |
|---|---|
| ELC-18B471L | COIL CHOKE 470UH RADIAL |
| PX0418/2M00 | CABLE IP68 4POS-6POS FIREWIRE 2M |
| 1-1624097-4 | INDUCTOR 470NH 1.7A SMD |
| Q2-F3X-1/4-01-SS250FT | HEATSHINK POLY 1/4" BLK 250' |
| GCM30DCSS | CONN EDGECARD 60POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-ADM1186-2EBZ | 功能描述:KIT EVALUATION FOR ADM1186-2 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| EVAL-ADM1186-2MBZ | 功能描述:KIT MICRO EVALUATION ADM1186-2 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:数字电位器 嵌入式:- 已用 IC / 零件:AD5258 主要属性:- 次要属性:- 已供物品:板 相关产品:AD5258BRMZ1-ND - IC POT DGTL I2C1K 64P 10MSOPAD5258BRMZ10-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ100-ND - IC POT DGTL I2C 100K 64P 10MSOPAD5258BRMZ50-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ1-R7-ND - IC POT DGTL I2C 1K 64P 10MSOPAD5258BRMZ10-R7-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ50-R7-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ100-R7-ND - IC POT DGTL I2C 100K 64P 10MSOP |
| EVAL-ADM1191EBZ | 功能描述:BOARD EVALUATION FOR ADM1191 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| EVAL-ADM1191EBZ1 | 制造商:AD 制造商全称:Analog Devices 功能描述:Digital Power Monitor with Convert Pin and ALERTB O |
| EVAL-ADM1192EBZ | 功能描述:BOARD EVALUATION FOR ADM1192 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
发布紧急采购，3分钟左右您将得到回复。