- 您现在的位置：买卖IC网 > Datasheet目录412 > EZLC-4421 LB (Silicon Laboratories Inc)KIT EZLINK F930/SI4421 LOW BAND Datasheet资料下载
参数资料
| 型号： | EZLC-4421 LB |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 29/45页 |
| 文件大小： | 0K |
| 描述： | KIT EZLINK F930/SI4421 LOW BAND |
| 标准包装： | 1 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页
Si4421
The best practice in interrupt handling is to start with a status read when interrupt occurs, and then make a decision based on the
status byte. It is very important to mention that any interrupt can “wake-up” the EZradio chip from sleep mode. This means that the
crystal oscillator starts to supply clock signal to the microcontroller even if the microcontroller has its own clock source. Also, the
Si4421 will not go to low current sleep mode if any interrupt remains active regardless to the state of the ex (enable crystal
oscillator) bit in the Power Management Command (page 15). This way the microcontroller always can have clock signal to process
the interrupt. To prevent high current consumption and this way short battery life, it is strongly advised to process and clear every
interrupt before going to sleep mode. All unnecessary functions should be turned off to avoid unwanted interrupts. Before freezing
the microcontroller code, a thorough testing must be performed in order to make sure that all interrupt sources are handled before
putting the radio device to low power consumption sleep mode. If the dc bit is set in the Power Management Command , then only
the ex bit controls the crystal oscillator (supposing that both the er and et bits are cleared), the interrupts have no effect on it.
TX REGISTER BUFFERED DATA TRANSMISSION
In this operating mode (enabled by bit el, in the Configuration Setting Command , page 15) the TX data is clocked into one of the two
8-bit data registers. The transmitter starts to send out the data from the first register (with the given bit rate) when bit et is set with
the Power Management Command (page 15). The initial value of the data registers (AAh) can be used to generate preamble. During
this mode, the SDO pin can be monitored to check whether the register is ready (SDO is high) to receive the next byte from the
microcontroller.
TX register simplified block diagram (before transmit)
TX register simplified block diagram (during transmit)
29
相关PDF资料 |
PDF描述 |
|---|---|
| F2M03G-KIT-1 | KIT EVAL G MOD SNGL (NO OEM BRD) |
| F2M03M-KIT-1 | KIT EVAL M MOD SNGL (NO OEM BRD) |
| FA10323_K2S-W | LENS FOR LUXEON K2 |
| FA10539_SSS-W | LENS FOR SEOUL P4 |
| FA10643_TINA-M | LENS FOR GOLDEN/PLATINUM DRAGON |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EZLC4431B1-D434 | 功能描述:射频开发工具 EZLink Kit F930 Si4431 Rev B1 434MHz RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| EZLC4431B1-D868 | 功能描述:射频开发工具 EZLink Kit F930 Si4431 Rev B1 868MHz RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| EZLC-4432 HB | 功能描述:射频开发工具 EZLink Fast Prototype Kit Hiband RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| EZLC-4432 HB/LB KIT | 制造商:Silicon Laboratories Inc 功能描述: |
| EZLC-4432 LB | 功能描述:射频开发工具 EZLink Fast Prototype Kit Lwband RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
发布紧急采购，3分钟左右您将得到回复。