- 您现在的位置：买卖IC网 > Datasheet目录412 > EZLC-4421 LB (Silicon Laboratories Inc)KIT EZLINK F930/SI4421 LOW BAND Datasheet资料下载
参数资料
| 型号： | EZLC-4421 LB |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 3/45页 |
| 文件大小： | 0K |
| 描述： | KIT EZLINK F930/SI4421 LOW BAND |
| 标准包装： | 1 |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页
Si4421
Data Validity Blocks
RSSI
A digital RSSI output is provided to monitor the input signal level.
It goes high if the received signal strength exceeds a given
preprogrammed level. An analog RSSI signal is also available.
The RSSI settling time depends on the external filter capacitor.
Pin 15 is used as analog RSSI output. The digital RSSI can be
monitored by reading the status register.
Typical Analog ARSSI Voltage vs. RF Input Power
DQD
The operation of the Data Quality Detector is based on counting
the spikes on the unfiltered received data. High output signal
indicates an operating FSK transmitter within baseband filter
bandwidth from the local oscillator. DQD threshold parameter
can be set by using the Data Filter Command (page 19) .
AFC
By using an integrated Automatic Frequency Control (AFC)
feature, the receiver can minimize the TX/RX offset in discrete
steps, allowing the use of:
? Narrower receiver bandwidth (i.e. increased
sensitivity)
? Higher data rate
? Inexpensive crystals
Crystal Oscillator
The Si4421 has a single-pin crystal oscillator circuit, which
provides a 10 MHz reference signal for the PLL. To reduce
external parts and simplify design, the crystal load capacitor is
internal and programmable. Guidelines for selecting the
appropriate crystal can be found later in this datasheet.
The transceiver can supply a clock signal for the microcontroller;
so accurate timing is possible without the need for a second
crystal.
When the microcontroller turns the crystal oscillator off by
suggested to turn the output buffer off by the Power
Management Command (page 15) .
Low Battery Voltage Detector
The low battery detector circuit monitors the supply voltage and
generates an interrupt if it falls below a programmable threshold
level. The detector circuit has 50 mV hysteresis.
Wake-Up Timer
The wake-up timer has very low current consumption (1.5 μA
typical) and can be programmed from 1 ms to several days with
an accuracy of ±10%.
The wake-up timer calibrates itself to the crystal oscillator at
every startup. For proper calibration of the wake-up timer the
crystal oscillator must be running before the wake-up timer is
enabled. The calibration process takes approximately 0.5ms.
For the crystal start up time (tsx), see page 11.
Event Handling
In order to minimize current consumption, the transceiver
supports different power saving modes. Active mode can be
initiated by several wake-up events (negative logical pulse on
nINT input, wake-up timer timeout, low supply voltage detection,
on-chip FIFO filled up or receiving a request through the serial
interface).
If any wake-up event occurs, the wake-up logic generates an
interrupt signal, which can be used to wake up the
microcontroller, effectively reducing the period the
microcontroller has to be active. The source of the interrupt can
be read out from the transceiver by the microcontroller through
the SDO pin.
Interface and Controller
An SPI compatible serial interface lets the user select the
frequency band, center frequency of the synthesizer, and the
bandwidth of the baseband signal path. Division ratio for the
microcontroller clock, wake-up timer period, and low supply
voltage detector threshold are also programmable. Any of these
auxiliary functions can be disabled when not needed. All
parameters are set to default after power-on; the programmed
values are retained during sleep mode. The interface supports
the read-out of a status register, providing detailed information
about the status of the transceiver and the received data.
The transmitter block is equipped with two 8-bit wide TX data
registers. It is possible to write 8 bits into the register in burst
mode and the internal bit rate generator transmits the bits out
with the predefined rate. For further details, see the TX Register
Buffered Data Transmission section (page 28).
It is also possible to store the received data bits into a FIFO
register and read them out in a buffered mode.
clearing the appropriate bit using the Power Management
Command (page 15), the chip provides a fixed number (192) of
further clock pulses (“clock tail”) for the microcontroller to let it
go to idle or sleep mode. If this clock output is not used, it is
3
相关PDF资料 |
PDF描述 |
|---|---|
| F2M03G-KIT-1 | KIT EVAL G MOD SNGL (NO OEM BRD) |
| F2M03M-KIT-1 | KIT EVAL M MOD SNGL (NO OEM BRD) |
| FA10323_K2S-W | LENS FOR LUXEON K2 |
| FA10539_SSS-W | LENS FOR SEOUL P4 |
| FA10643_TINA-M | LENS FOR GOLDEN/PLATINUM DRAGON |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EZLC4431B1-D434 | 功能描述:射频开发工具 EZLink Kit F930 Si4431 Rev B1 434MHz RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| EZLC4431B1-D868 | 功能描述:射频开发工具 EZLink Kit F930 Si4431 Rev B1 868MHz RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| EZLC-4432 HB | 功能描述:射频开发工具 EZLink Fast Prototype Kit Hiband RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| EZLC-4432 HB/LB KIT | 制造商:Silicon Laboratories Inc 功能描述: |
| EZLC-4432 LB | 功能描述:射频开发工具 EZLink Fast Prototype Kit Lwband RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
发布紧急采购，3分钟左右您将得到回复。