- 您现在的位置：买卖IC网 > PDF目录67412 > FA7703V (FUJI ELECTRIC CO LTD) 0.4 A DUAL SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 PDF资料下载
参数资料
| 型号： | FA7703V |
| 厂商： | FUJI ELECTRIC CO LTD |
| 元件分类： | 稳压器 |
| 英文描述： | 0.4 A DUAL SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封装： | 1.10 MM, TSSOP-16 |
| 文件页数： | 7/21页 |
| 文件大小： | 242K |
| 代理商： | FA7703V |
15
Quality is our message
FA7703/04
function can be calculated with
CS
I
C
0.7
tp[s]
×
≈
where, CCS: Capacitance of CS terminal [
F]
ICS: Output source current of CS terminal [
A]
(2.
2Α, typ.)
You can reset the timer latch action for the
short-circuit protection function by changing the
voltage of either VCC terminal or CS terminal to
the following values.
VCC terminal: below UVLO voltage (1.85V typ.)
CS terminal: below 1.83V(typ.)
(7)Output circuit
FA7703/04 contain a push-pull output stage
and can directly drive MOSFETs. The peak
current of OUT terminal is the maximum sink
current of +150mA, and the source current of
-400mA. FA7703/04 can also drive both NPN
and PNP type transistors. And in such cases,
the maximum continuous current is ±50mA.
When designing the value of output current, be
sure to consider the allowable loss accordingly.
(See Design advice)
Ch1 of FA7703/04 is available for driving both
types of MOSFETs and you can determine the
type of MOSFET, which is connected externally
by selecting the connection of SEL1 terminal
(Pin11). If SEL terminal is connected to GND
terminal, FA7703/04 can drive a Pch MOSFET. If
SEL terminal is connected to REG terminal, they
can drive Nch MOSFET.
You can accordingly design a buck converter
circuit by Pch MOSFET driving, and a boost
circuit or a fly-back converter circuit by Nch
MOSFET driving.
DO NOT leave SEL1 terminal open in operation,
and be sure to connect it to either GND terminal
or REG terminal.
(8)Power good signal/Undervoltage lockout
protection circuit (UVLO)
To protect FA7703/04 from malfunction when
the supply voltage drops, there is built-in
undervoltage lockout as a protection circuit.
When the supply voltage rises from 0V, the
UVLO circuit is canceled at VCC of 2.0V(typ.).
When the supply voltage drops, the UVLO circuit
shuts off the output at VCC of 1.85V(typ.). In this
case, CS terminal is reset to Low level.
Power good signal circuit monitors the voltage
of REG terminal, and it stops the output of
FA7703/04 until the voltage of REG terminal
exceeds approximately 1.9V in order to protect
the ICs from malfunction.
Fig.7
0.5
1.5
1.0
2.0
Start-up
soft start
momentary short circuit
short circuit
protection
tp
Time
CS
terminal
voltage
[V]
1.27V
2.2V
0
相关PDF资料 |
PDF描述 |
|---|---|
| FA7704M | 0.4 A DUAL SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| FA7703M | 0.4 A DUAL SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| FA7738N | 5.5 A SWITCHING REGULATOR, 400 kHz SWITCHING FREQ-MAX, PDSO8 |
| FA7738P | 5.5 A SWITCHING REGULATOR, 400 kHz SWITCHING FREQ-MAX, PDIP8 |
| FAB2200UCX | 1.2 W, 2 CHANNEL, AUDIO AMPLIFIER, PBGA25 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FA7704 | 制造商:FUJI 制造商全称:Fuji Electric 功能描述:FUJI Power Supply Control IC |
| FA771 | 制造商:Black Box Corporation 功能描述:DB25 TO RJ45,8 WIRE,F MOD THUMBSCREW ADPTR KIT |
| FA7711V | 制造商:FUJI 制造商全称:Fuji Electric 功能描述:FUJI Power Supply Control IC |
| FA7726 | 制造商:FUJI 制造商全称:Fuji Electric 功能描述:45V Input Buck Converter 3ch/2ch IC with Power MOSFET |
| FA7730 | 制造商:FUJI 制造商全称:Fuji Electric 功能描述:45V Input Buck Converter 3ch/2ch IC with Power MOSFET |
发布紧急采购，3分钟左右您将得到回复。