- 您现在的位置：买卖IC网 > PDF目录172369 > FAN5094MTC (FAIRCHILD SEMICONDUCTOR CORP) PDF资料下载
参数资料
| 型号： | FAN5094MTC |
| 厂商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分类： | 稳压器 |
| 中文描述： | 3 A SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封装： | TSSOP-28 |
| 文件页数： | 9/22页 |
| 文件大小： | 182K |
| 代理商： | FAN5094MTC |
PRODUCT SPECIFICATION
FAN5094
REV. 1.0.2 5/13/02
17
Output Enable/Soft Start (ENABLE/SS)
The FAN5094 will accept an open collector/TTL signal for
controlling the output voltage. The low state disables the
output voltage. When disabled, the PWRGD output is in the
low state.
Even if an enable is not required in the circuit, this pin
should have attached a capacitor (typically 100nF) to soft-
start the switching. A softstart capacitor may be approxi-
mately chosen by the formula:
However, C must be
≥ 100nF.
Oscillator
The FAN5094 oscillator section runs at a frequency deter-
mined by a resistor from the RT pin to ground according to
the formula
The oscillator generates two square waves, 180° out of phase
with each other. One is used internally, the other is sent to a
second FAN5094 on the CLK pin.
The square wave generates two internal sawtooth ramps,
each at one-half the square wave frequency, and running
180
° out of phase with each other. These ramps cause the
turn-on time of the two phases to be phased apart and the
four phases to be 90° apart each. The oscillator frequency of
the FAN5094 can be programmed from 400KHz to 4MHz
with each phase running at 100KHz to 1MHz, respectively.
Selection of a frequency will depend on various system
performance criteria, with higher frequency resulting in
smaller components but lower efciency.
Programmable Active Droop
The FAN5094 features Programmable Active Droop: as
the output current increases, the output voltage drops propor-
tionately an amount that can be programmed with an exter-
nal resistor. This feature is offered in order to allow
maximum headroom for transient response of the converter.
The current is sensed losslessly by measuring the voltage
across the low-side MOSFET during its on time. Consult the
section on current sensing for details. Note that this method
makes the droop dependent on the temperature and initial
tolerance of the MOSFET, and the droop must be calculated
taking account of these tolerances. Given a maximum load
current, the amount of droop can be programmed with a
resistor to ground on the droop pin, according to the formula
with VDroop the desired droop voltage, RT the oscillator
resistor, Imax the load current at which the droop is desired,
n the number of phases, and RDS, on the on-state resistance of
one phase’s low-side MOSFET.
Typical response time of the FAN5094 to an output voltage
change is 100nsec.
Important Note! The oscillator frequency must be selected
before selecting the droop resistor, because the value of RT
is used in the calculation of RDroop.
Over-Voltage Protection
The FAN5094 constantly monitors the output voltage for
protection against over-voltage conditions. If the voltage at
the VFB pin exceeds 2.2V, an over-voltage condition is
assumed and the FAN5094 latches on the external low-side
MOSFET and latches off the high-side MOSFET. The
DC-DC converter returns to normal operation only after VCC
has been recycled.
Thermal Design Considerations
Because of the very large gate capacitances that the
FAN5094 may be driving, the IC may dissipate substantial
power. It is important to provide a path for the IC’s heat to be
removed, to avoid overheating. In practice, this means that
each of the pins should be connected to as large a trace as
possible. Use of the heavier weights of copper on the PCB is
also desirable. Since the MOSFETs also generate a lot of
heat, efforts should be made to thermally isolate them from
the IC.
Over Temperature Protection
If the FAN5094 die temperature exceeds approximately
150
°C, the IC shuts itself off. It remains off until the temper-
ature has dropped approximately 25
°C, at which time it
resumes normal operation.
Component Selection
MOSFET Selection
This application requires N-channel Enhancement Mode Field
Effect Transistors. Desired characteristics are as follows:
Low Drain-Source On-Resistance,
RDS,ON < 10m
(lower is better);
Power package with low Thermal Resistance;
Drain-Source voltage rating > 15V;
Low gate charge, especially for higher frequency
operation.
For the low-side MOSFET, the on-resistance (RDS,ON) is the
primary parameter for selection. Because of the small duty
cycle of the high-side, the on-resistance determines the
power dissipation in the low-side MOSFET and therefore
signicantly affects the efciency of the DC-DC converter.
For high current applications, it may be necessary to use two
MOSFETs in parallel for the low-side for each phase.
C
t10
A
1V
out
+
----------------------
=
RT
()
50
10
9
fHz
()
----------------------
=
R
Droop
()
2n
V
Droop
RT
I
max
R
DS on
,
---------------------------------------------------
=
相关PDF资料 |
PDF描述 |
|---|---|
| FAN5341UMPX | |
| FAN5353MPX | |
| FAN5354MPX | |
| FAN5660IM | |
| FAN5902MPX | |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FAN5094MTC_Q | 功能描述:DC/DC 开关控制器 Buck Converter Hi Cur Sys Voltage RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| FAN5094MTCX | 功能描述:DC/DC 开关控制器 Buck Converter Hi Cur Sys Voltage RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| FAN5098 | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:Two Phase Interleaved Synchronous Buck Converter for AMD Hammer⑩ |
| FAN5098-BAB3116B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN5098-BCB3116B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。