- 您现在的位置：买卖IC网 > PDF目录1792 > FDMF6705 (Fairchild Semiconductor)MODULE DRMOS HI PERF HF POWER66 PDF资料下载
参数资料
| 型号： | FDMF6705 |
| 厂商： | Fairchild Semiconductor |
| 文件页数： | 16/19页 |
| 文件大小： | 0K |
| 描述： | MODULE DRMOS HI PERF HF POWER66 |
| 标准包装： | 3,000 |
| 系列： | XS™ DrMOS |
| 类型： | 高端/低端驱动器 |
| 输入类型： | PWM |
| 输出数： | 1 |
| 电流 - 峰值输出： | 40A |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-PowerTFQFN |
| 供应商设备封装： | 40-PQFN（6x6） |
| 包装： | 带卷 (TR) |
PCB Layout Guidelines
Figure 30 provides an example of a proper layout for the
FDMF6705 and critical components. All of the high-
current paths, such as V IN , V SWH , V OUT , and GND
copper, should be short and wide for low inductance
and resistance. This technique aids in achieving a more
stable and evenly distributed current flow, along with
enhanced heat radiation and system performance.
The following guidelines are recommendations for the
PCB designer:
1. Input ceramic bypass capacitors must be placed
close to the VIN and PGND pins. This helps
reduce the high-current power loop inductance
and the input current ripple induced by the power
MOSFET switching operation.
2. The V SWH copper trace serves two purposes. In
addition to being the high-frequency current path
from the DrMOS package to the output inductor, it
also serves as a heat sink for the low-side
MOSFET in the DrMOS package. The trace
should be short and wide enough to present a low-
impedance path for the high-frequency, high-
current flow between the DrMOS and inductor to
minimize losses and temperature rise. Note that
the VSWH node is a high voltage and high-
frequency switching node with high noise
potential. Care should be taken to minimize
coupling to adjacent traces. Since this copper
trace also acts as a heat sink for the lower FET,
balance using the largest area possible to improve
DrMOS cooling while maintaining acceptable
noise emission.
3. An output inductor should be located close to the
FDMF6705 to minimize the power loss due to the
VSWH copper trace. Care should also be taken so
the inductor dissipation does not heat the DrMOS.
4. PowerTrench? MOSFETs are used in the output
stage. The Power MOSFETs are effective at
minimizing ringing due to fast switching. In most
cases, no VSWH snubber is required. If a snubber
is used, it should be placed close to the VSWH and
PGND pins. The resistor and capacitor need to be
of proper size for the power dissipation.
5. VCIN, VDRV, and BOOT capacitors should be
placed as close as possible to the VCIN to CGND,
VDRV to CGND, and BOOT to PHASE pins to
ensure clean and stable power. Routing width and
length should be considered as well.
6. Include a trace from PHASE to VSWH to improve
noise margin. Keep the trace as short as possible.
7. The layout should include a placeholder to insert a
small-value series boot resistor (R BOOT ) between
? 2011 Fairchild Semiconductor Corporation
FDMF6705 ? Rev. 1.0.4
16
the boot capacitor (C BOOT ) and DrMOS BOOT pin.
The BOOT-to-VSWH loop size, including R BOOT
and C BOOT , should be as small as possible. The
boot resistor may be required when operating near
the maximum rated V IN . The boot resistor is
effective at controlling the high-side MOSFET turn-
on slew rate and V SHW overshoot. R BOOT can
improve noise operating margin in synchronous
buck designs that may have noise issues due to
ground bounce or high positive and negative
VSWH ringing. However, inserting a boot
resistance lowers the DrMOS efficiency. Efficiency
versus noise trade-offs must be considered. R BOOT
values from 0.5 ? to 3.0 ? are typically effective in
reducing VSWH overshoot for the FDMF6705.
The VIN and PGND pins handle large current
transients with frequency components greater than
100MHz. If possible, these pins should be
connected directly to the VIN and board GND
planes. The use of thermal relief traces in series
with these pins is discouraged since this adds
inductance to the power path. This added
inductance in series with either the VIN or PGND
pin degrades system noise immunity by increasing
positive and negative VSWH ringing.
8. CGND pad and PGND pins should be connected to
the GND plane copper with multiple vias for stable
grounding. Poor grounding can create a noise
transient offset voltage level between CGND and
PGND. This could lead to faulty operation of the
gate driver and MOSFETs.
9. Ringing at the BOOT pin is most effectively
controlled by close placement of the boot
capacitor. Do not add an additional BOOT to the
PGND capacitor. This may lead to excess current
flow through the BOOT diode.
10. The SMOD# and DISB# pins have weak internal
pull-up and pull-down current sources,
respectively. These pins should not have any
noise filter capacitors. Do not to float these pins
unless absolutely necessary.
11. Use multiple vias on each copper area to
interconnect top, inner, and bottom layers to help
distribute current flow and heat conduction. Vias
should be relatively large and of reasonably low
inductance. Critical high-frequency components,
such as R BOOT , C BOOT , the RC snubber, and
bypass capacitors should be located as close to
the respective DrMOS module pins as possible
on the top layer of the PCB. If this is not feasible,
they should be connected from the backside
through a network of low-inductance vias.
www.fairchildsemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| FDMF6706B | MODULE DRMOS 45A 40-PQFN |
| FDMF6706C | MODULE DRMOS 40A 1000KHZ 40PQFN |
| FDMF6707B | MODULE DRMOS 50A 300KHZ 40PQFN |
| FDMF6707C | MODULE DRMOS 50A 40-PQFN |
| FDMF6707V | MODULE DRMOS 50A 40-PQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FDMF6705B | 功能描述:功率驱动器IC Xtra-Small Hi-Perf Hi-Freq DrMOS Module RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| FDMF6705V | 功能描述:功率驱动器IC XS DrMOS; Hi-Freq Hi-Perf Module RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| FDMF6706B | 功能描述:功率驱动器IC Xtra-Small Hi-Perf Hi-Freq DrMOS Module RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| FDMF6706C | 功能描述:功率驱动器IC XS DrMOS; Hi-Freq Hi-Perf Module RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| FDMF6707B | 功能描述:功率驱动器IC XS DrMOS; Hi-Freq Hi-Perf Module RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。