- 您现在的位置：买卖IC网 > PDF目录17241 > FEB167 (Fairchild Semiconductor)BOARD EVAL FOR FAN2106 PDF资料下载
参数资料
| 型号： | FEB167 |
| 厂商： | Fairchild Semiconductor |
| 文件页数： | 10/15页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR FAN2106 |
| 标准包装： | 1 |
| 系列： | TinyBuck™ |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 1，非隔离 |
| 输出电压： | 1.8V |
| 电流 - 输出： | 6A |
| 输入电压： | 8 ~ 20 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 500kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | FAN2106 |
| 相关产品： | FAN2106EMPXDKR-ND - IC REG BUCK SYNC ADJ 6A 25MLP FAN2106EMPXCT-ND - IC REG BUCK SYNC ADJ 6A 25MLP FAN2106EMPXTR-ND - IC REG BUCK SYNC ADJ 6A 25MLP FAN2106MPXDKR-ND - IC REG BUCK SYNC ADJ 6A 25MLP FAN2106MPXCT-ND - IC REG BUCK SYNC ADJ 6A 25MLP FAN2106MPXTR-ND - IC REG BUCK SYNC ADJ 6A 25MLP |
Circuit Description
PWM Generation
Soft-start time is a function of switching frequency.
Refer to Figure 2 for the PWM control mechanism.
FAN2106 uses the summing-mode method of control to
generate the PWM pulses. An amplified current-sense
EN
1.35V
signal is summed with an internally generated ramp and
the combined signal is compared with the output of the
2400 CLKs
0.8V
error amplifier to generate the pulsewidth to drive the
high-side MOSFET. Sensed current from the previous
cycle is used to modulate the output of the summing
FB
Fault
block. The output of the summing block is also
compared against a voltage threshold set by the R LIM
resistor to limit the inductor current on a cycle-by-cycle
basis. The R RAMP resistor helps set the charging current
for the internal ramp and provides input voltage feed-
SS
1.0V
0.8V
Latch
Enable
forward function. The controller facilitates external
compensation for enhanced flexibility.
Initialization
Once V CC exceeds the UVLO threshold and EN is HIGH,
the IC checks for a shorted FB pin before releasing the
internal soft-start ramp (SS).
If the parallel combination of R1 and R BIAS is ≤ 1 K Ω , the
internal SS ramp is not released and the regulator does
not start.
Enable
FAN2106 has an internal pull-up to the ENABLE (EN)
pin so that the IC is enabled once V CC exceeds the
UVLO threshold. Connecting a small capacitor across
EN and AGND delays the rate of voltage rise on the EN
pin. The EN pin also serves for the restart whenever a
fault occurs (refer to the Auto-Restart section) . If the
regulator is enabled externally, the external EN signal
should go HIGH only after V CC is established. For
applications where such sequencing is required,
FAN2106 can be enabled (after the V CC comes up) with
external control, as shown in Figure 21.
Figure 21. Enabling with External Control
Soft-Start
Once internal SS ramp has charged to 0.8 V (T0.8), the
output voltage is in regulation. Until SS ramp reaches
1.0 V (T1.0), the fault latch is inhibited.
To avoid skipping the soft-start cycle, it is necessary to
apply V IN before V CC reaches its UVLO threshold. Normal
sequence for powering up would be VIN ? VCC ? EN.
? 2009 Fairchild Semiconductor Corporation
FAN2106 ? Rev. 1.1.2
10
3200 CLKs
T0.8
4000 CLKs
T1.0
Figure 22. Soft-Start Timing Diagram
Cycling V CC or the EN pin discharges the internal SS
and resets the IC. In applications where external EN
signal is used, V IN and V CC should be established before
the EN signal comes up to prevent skipping the soft-
start function.
Startup on Pre-Bias
The regulator does not allow the low-side MOSFET to
operate in full synchronous rectification mode until
internal SS ramp reaches 95% of V REF (~0.76 V). This
helps the regulator start on a pre-biased output and
ensures that the pre-biased outputs are not discharged
during soft-start.
Protections
The converter output is monitored and protected against
extreme overload, short-circuit, over-voltage, under-
voltage, and over-temperature conditions.
Under-Voltage Shutdown
If the voltage on the FB pin remains below the under-
voltage threshold for 16 consecutive clock cycles, the
fault latch is set and the converter shuts down. This
protection is not active until the internal SS ramp
reaches 1.0 V during soft-start.
Over-Voltage Protection
If voltage on the FB pin exceeds 115% of V REF for two
consecutive clock cycles, the fault latch is set and
shutdown occurs.
A shorted high-side MOSFET condition is detected
when SW voltage exceeds ~0.7 V while the low-side
www.fairchildsemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| RBM06DCSH | CONN EDGECARD 12POS DIP .156 SLD |
| 45222C | INDUCTOR 2.2UH 4.5A SMD SHIELDED |
| 195D476X0010Z2W | CAP TANT 47UF 10V 20% 2910 |
| T95S335M016LZSL | CAP TANT 3.3UF 16V 20% 1507 |
| T95S335K016LZSL | CAP TANT 3.3UF 16V 10% 1507 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FEB173 | 功能描述:电源管理IC开发工具 Evaluation Board for FAN5336MPX RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| FEB175 | 功能描述:电源管理IC开发工具 Evaluation Board for FAN5617 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| FEB176 | 功能描述:电源管理IC开发工具 Evaluation Board for FAN5631 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| FEB178 | 功能描述:电源管理IC开发工具 Evaluation Board for FAN5350MPX RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| FEB179 | 功能描述:电源管理IC开发工具 Evaluation Board for FAN5350UCX RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。