- 您现在的位置：买卖IC网 > PDF目录67478 > FK1501-7RD0TB2 (POWER-ONE INC) 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | FK1501-7RD0TB2 |
| 厂商： | POWER-ONE INC |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
| 封装： | METAL, CASE K02, MODULE |
| 文件页数： | 4/31页 |
| 文件大小： | 1251K |
| 代理商： | FK1501-7RD0TB2 |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
K Series
DC-DC Converters >100 Watt
Rugged Environment
Edition 4/4.99
12/31
MELCHER
The Power Partners.
Output Protection
Each output is protected against overvoltages which could
occur due to a failure of the internal control circuit. Voltage
suppressor diodes (which under worst case condition may
become a short circuit) provide the required protection. The
suppressor diodes are not designed to withstand externally
applied overvoltages. Overload at any of the outputs will
cause a shut-down of all outputs. A red LED indicates the
overload condition.
Parallel or Series Connection of Units
Single or double output units with equal nominal output
voltage can be connected in parallel without any precau-
tions using option T.
With option T (current sharing), all units share the current
approximately equally.
Single output units and/or main and second outputs of dou-
ble output units can be connected in series with any other
(similar) output.
Note:
– Parallel connection of double output units should always
include both, main and second output to maintain good
regulation of both outputs.
– Not more than 5 units should be connected in parallel.
– Series connection of second outputs without involving
their main outputs should be avoided as regulation may
be poor.
– The maximum output current is limited by the output with
the lowest current limitation if several outputs are con-
nected in series.
Thermal Considerations
If a converter is located in free, quasi-stationary air (con-
vection cooling) at the indicated maximum ambient tem-
perature
TA max (see table: Temperature specifications) and
is operated at its nominal input voltage and output power,
the temperature measured at the
Measuring point of case
temperature TC (see: Mechanical Data) will approach the
indicated value
TC max after the warm-up phase. However,
the relationship between
TA and TC depends heavily on the
conditions of operation and integration into a system. The
thermal conditions are influenced by input voltage, output
current, airflow and temperature of surrounding compo-
nents and surfaces.
TA max is therefore, contrary to TC max,
an indicative value only.
Caution: The installer must ensure that under all operat-
ing conditions
TC remains within the limits stated in the
table
Temperature specifications.
Notes: Sufficient forced cooling or an additional heat sink
allows
TA to be higher than 71°C (e.g. 85°C) if TC max is not
exceeded.
For -7 or -9 units at an ambient temperature
TA of 85
°C with
only convection cooling, the maximum permissible current
for each output is approx. 40% of its nominal value as per
figure.
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
50
60
70
80
90
100
Io/Io nom
TA [°C]
0.9
1.0
Forced cooling
05089
TA min
TC max
Convection cooling
Fig. 7
Output current derating versus temperature for -7 and -9
units.
Thermal Protection
A temperature sensor generates an internal inhibit signal
which disables the outputs if the case temperature exceeds
TC max. The outputs are automatically re-enabled if the tem-
perature drops below this limit.
It is recommended that continuous operation under simul-
taneous extreme worst case conditions of the following
three parameters be avoided: Minimum input voltage,
maximum output power and maximum temperature.
Uo1d
t d
Ur
t
Uo2d
<10
s
<10
s
Uo1
Uo2
Io1/Io1 nom
0
0.5
1
Io2/Io2 nom
05072
Fig. 8
Typical dynamic load regulation of Uo1 and Uo2
相关PDF资料 |
PDF描述 |
|---|---|
| FK1501-9PD0B2 | 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
| FK1501-9PD8TB2 | 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
| FK1501-9RDDT | 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
| FK1601-9PD8B2 | 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
| FK1601-9RD8TB2 | 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FK1501-9ER | 制造商:Power-One 功能描述:DCDC - Bulk |
| F-K15-1 | 制造商:Cosel Usa Inc 功能描述:Optional Accessories, OP Series |
| F-K15-2 | 制造商:Cosel Usa Inc 功能描述:Optional Accessories, OP Series |
| FK15M | 功能描述:TAPERED END PENETRATION PROBE RoHS:是 类别:测试设备 >> 测试引线 - 热电偶，温度探头 系列:FK 标准包装:1 系列:6543 类型:J 型热电偶 使用:液体，半固体 尖端 - 类型:防浸渍 / 穿透式，圆头 插头类型:超微型（热电偶插头） 探针温度范围:-40 ~ 2000°F（-40 ~ 1093°C） 线缆长度:- 线缆绝缘:- 插头颜色:黑 探针长度:12.000"（304.80mm） 探针材料:- |
| FK15S BLK | 制造商:SCHUTZINGER 功能描述:4MM PLG STACK BLACK |
发布紧急采购，3分钟左右您将得到回复。