- 您现在的位置：买卖IC网 > PDF目录67504 > FM3316-G SPECIALTY CONSUMER CIRCUIT, PDSO14 PDF资料下载
参数资料
| 型号： | FM3316-G |
| 元件分类： | 消费家电 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PDSO14 |
| 封装： | GREEN, MO-012AB, SOIC-14 |
| 文件页数： | 24/28页 |
| 文件大小： | 320K |
| 代理商： | FM3316-G |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页
FM33256/FM3316 SPI Companion w/ FRAM
Rev. 2.0
Feb. 2009
Page 5 of 28
60 ms increments via a 5-bit nonvolatile setting
(register 0Ch).
Figure 3. Watchdog Timer
The watchdog also incorporates a window timer
feature that allows a delayed start. The starting time
and ending time defines the window and each may be
set independently.
The starting time has 25 ms
resolution and 0 ms to 775 ms range.
Figure 4. Window Timer
The watchdog EndTime value is located in register
0Ch, bits 4-0, the watchdog enable is bit 7. The
watchdog is restarted by writing the pattern 1010b to
the lower nibble of register 0Ah. Writing the correct
pattern will also cause the timer to load new timeout
values. Writing other patterns to this address will not
affect its operation. Note the watchdog timer is free-
running. Prior to enabling it, users should restart the
timer as described above. This assures that the full
timeout is provided immediately after enabling. The
watchdog is disabled when VDD drops below VTP.
Note setting the EndTime timeout setting to all
zeroes (00000b) disables the timer to save power.
The listing below summarizes the watchdog bits.
Watchdog StartTime
WDST4-0 0Bh, bits 4-0
Watchdog EndTime
WDET4-0 0Ch, bits 4-0
Watchdog Enable
WDE
0Ch, bit 7
Watchdog Restart
WR3-0
0Ah, bits 3-0
Watchdog Flags
EWDF,
09h, bit 7
LWDF
09h, bit 6
The programmed StartTime value is a guaranteed
maximum time while the EndTime value is a
guaranteed minimum time, and both vary with
temperature and VDD voltage. The watchdog has two
additional controls associated with its operation. The
nonvolatile enable bit WDE allows the /RST to go
active if the watchdog reaches the timeout without
being restarted. If a reset occurs, the timer will restart
on the rising edge of the reset pulse. If WDE is not
enabled, the watchdog timer still runs but has no
effect on /RST. The second control is a nibble that
restarts the timer, thus preventing a reset. The timer
should be restarted after changing the timeout value.
This procedure must be followed to properly load the
watchdog registers:
Address
1.
Write the StartTime value
0Bh
2.
Write the EndTime value and WDE=1 0Ch
3.
Issue a Restart command
0Ah
The restart command in step 3 must be issued before
tDOG2, which was programmed in step 2. The window
timer starts counting when the restart command is
issued.
Manual Reset
The /RST is a bi-directional signal allowing the
FM33xx to filter and de-bounce a manual reset
switch. The /RST input detects an external low
condition and responds by driving the /RST signal
low for 100 ms (max.). This effectively filters and de-
bounces a reset switch. After this timeout (tRPW), the
user may continue pulling down on the /RST pin, but
SPI commands will not be locked out.
Figure 5. Manual Reset
Note the internal weak pull-up eliminates the need
for additional external components.
Reset Flags
In case of a reset condition, a flag bit will be set to
indicate the source of the reset. A low-VDD reset is
indicated by the POR bit, register 09h bit 5. There are
two watchdog reset flags
- one for an early fault
(EWDF) and the other for a late fault (LWDF),
located in register 09h bits 7 and 6. A manual reset
will result in no flag being set, so the absence of a
flag is a manual reset. Note that the bits are set in
response to reset sources but they must be cleared by
the user. It is possible to read the register and have
RST
Watchdog
Restart
Start
Time
End
Time
100 ms (max)
Window
Timebase
Down Counter
Watchdog
Timer Settings
100 ms
clock
WDE
/RST
WR3-0 = 1010b
to restart
FM33xx
Reset
Switch
RST
MCU
Switch
Behavior
RST
FM33xx
drives
100 ms (max.)
相关PDF资料 |
PDF描述 |
|---|---|
| FM33256-GTR | SPECIALTY CONSUMER CIRCUIT, PDSO14 |
| FM33256-G | SPECIALTY CONSUMER CIRCUIT, PDSO14 |
| FM4005-G | SPECIALTY CONSUMER CIRCUIT, PDSO14 |
| FME270-461/ES | 1 FUNCTIONS, 400 V, 1.5 A, DATA LINE FILTER |
| FME270-461V/ES | 1 FUNCTIONS, 400 V, 1.5 A, DATA LINE FILTER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FM3316-GTR | 功能描述:F-RAM 16K w/Pwr Mon WDT Bat Sw Pwr Fail RoHS:否 存储容量:512 Kbit 组织:64 K x 8 接口:SPI 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube 制造商:Cypress Semiconductor |
| FM33256 | 制造商:RAMTRON 制造商全称:RAMTRON 功能描述:3V Integrated Processor Companion with Memory |
| FM33256_09 | 制造商:RAMTRON 制造商全称:RAMTRON 功能描述:3V Integrated Processor Companion with Memory |
| FM33256B | 制造商:CYPRESS 制造商全称:Cypress Semiconductor 功能描述:3V Integrated Processor Companion with F-RAM |
| FM33256B-G | 功能描述:实时时钟 256Kb F-RAM Processor Companion RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。