- 您现在的位置：买卖IC网 > PDF目录15800 > FR3-8M (TechTools)EMULATOR FLASH FLEXROM III 8MEG PDF资料下载
参数资料
| 型号： | FR3-8M |
| 厂商： | TechTools |
| 文件页数： | 24/38页 |
| 文件大小： | 0K |
| 描述： | EMULATOR FLASH FLEXROM III 8MEG |
| 标准包装： | 1 |
| 系列： | FlexROM™ III |
| 类型： | 存储器 |
| 适用于相关产品： | 外部 FLASH、EPROM 或 SRAM 设备 |
| 所含物品： | 需要 FR3 FlexROM III 仿真器、缆线（菊花链、LPT、迷你型夹和目标）、软件、有源缆线模块 |
| 其它名称： | FR38M |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
Fast CS Access
Normally, FlexROM III drives its SRAM CS (chip select) lines with a buffered version of your target’s CS
line and provides stable data 45ns after the last transition on address or after CS goes active – whichever is
later.
Enabling FAST CS ACCESS causes FlexROM III to force its SRAM CS lines always active. FlexROM
III’s output buffers are still gated with your target CS so the emulator continues to honor all target control
signals. This reduces the emulator’s Tcs access time from 45ns to 12ns.
Many targets will decode their CS signal off of address lines. This makes the Tcs the determining factor in
setting its ACCESS time requirements. The Tacc might be 45ns but due to decoding delays, the Tcs could
be 30 – 40ns. In this situation, the FAST CS option would allow our 45ns emulator to function properly in
a target that normally requires a 30-40ns emulator.
You normally would not turn this option on unless your target has a Tcs requirement of < 45ns and its
addresses are stable before CS is activated.
Turning on this option will result in higher operating current requirements and could increase system noise
in targets that have extended periods of address line float.
Fast OE Access
Normally, FlexROM III drives its SRAM OE (output enable) lines with a buffered version of your target’s
OE line and provides stable data 45ns after the last transition on address or after CS goes active, or 30ns
after OE goes active – whichever is later.
Enabling FAST OE ACCESS causes FlexROM III to force its SRAM OE lines always active. FlexROM
III’s output buffers are still gated with your target OE so the emulator continues to honor all target control
signals. This reduces the emulator’s OE access time from 30ns to 12ns.
Turning on this option will result in slightly higher operating current requirements and could increase
system noise in some targets during target writes to the emulator.
You normally would not turn on this option unless your target has a Toe timing specification of < 30ns.
However, it generally does not hurt to do so.
It is acceptable to use FAST CS and FAST OE at the same time.
FlexROM III User’s Manual
22
Copyright ? 2001, TechTools
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B7W-EY-F4 | CONVERTER MOD DC/DC 5.5V 50W |
| TC1270AMVCTTR | IC RESET MONITOR 4.38V SOT23A-5 |
| VE-B7W-EY-F3 | CONVERTER MOD DC/DC 5.5V 50W |
| TC1270ALVRCTR | IC RESET MONITOR 4.63V SOT143-4 |
| VE-B7W-EY-F2 | CONVERTER MOD DC/DC 5.5V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FR3A | 制造商:SEMIKRON 制造商全称:Semikron International 功能描述:Fast silicon rectifier diodes |
| FR3A_06 | 制造商:WTE 制造商全称:Won-Top Electronics 功能描述:3.0A SURFACE MOUNT GLASS PASSIVATED FAST RECOVERY DIODE |
| FR3A_07 | 制造商:SEMIKRON 制造商全称:Semikron International 功能描述:Fast silicon rectifier diodes |
| FR3A_09 | 制造商:PANJIT 制造商全称:Pan Jit International Inc. 功能描述:FAST SWITCHING SURFACE MOUNT RECTIFIER |
| FR3A_11 | 制造商:MCC 制造商全称:Micro Commercial Components 功能描述:3 Amp Fast Recovery Silicon Rectifier 50 to 1000 Volts |
发布紧急采购，3分钟左右您将得到回复。