- 您现在的位置：买卖IC网 > PDF目录15800 > FR3-8M (TechTools)EMULATOR FLASH FLEXROM III 8MEG PDF资料下载
参数资料
| 型号： | FR3-8M |
| 厂商： | TechTools |
| 文件页数： | 34/38页 |
| 文件大小： | 0K |
| 描述： | EMULATOR FLASH FLEXROM III 8MEG |
| 标准包装： | 1 |
| 系列： | FlexROM™ III |
| 类型： | 存储器 |
| 适用于相关产品： | 外部 FLASH、EPROM 或 SRAM 设备 |
| 所含物品： | 需要 FR3 FlexROM III 仿真器、缆线（菊花链、LPT、迷你型夹和目标）、软件、有源缆线模块 |
| 其它名称： | FR38M |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页当前第34页第35页第36页第37页第38页
FAQs
Can I use FlexROM III on a 3V target?
YES, but you will need an external power supply. Connect 5VDC at 300ma or greater to the emulator’s
external power connector. External power supplies are available form TechTools.
What is the lowest target voltage supported?
FlexROM III was designed to support 3.0V to 5.0V targets. However, it CAN support lower voltage targets
within limits. Three things set the lower limit; Logic INPUT thresholds, Vout HIGH from the emulator,
and the target isolation threshold.
-
-
-
Logic INPUT Thresholds. FlexROM III will accept a Vin HIGH minimum of 1.5Volts. Your
target MUST produce at least 1.5V for logic HIGHs. Most logic down to about 2V can meet this
requirement.
Vout HIGH levels: Your target must tolerate logic HIGHs from the emulator data lines of
3.2Volts. This depends entirely on your target design.
Target Isolation Threshold: To allow safe target power cycling,, FlexROM III constantly monitors
the target’s voltage. When it detects that the target voltage has dropped below a fixed threshold, it
assumes the target is powering down so it turns off its output buffers to avoid leaking current into
the target. It also asserts reset and turns the STATUS LED RED. If the emulator did NOT
provide this safety feature, it could start reverse biasing devices on the target, potentially causing
damage. Even if the target were not damaged, the current leakage could prevent the target from
properly powering down. This could prevent the reset circuitry from operating. This cut-off
threshold is approximate 2.7 to 2.8V.
Bottom line: You CAN emulate lower voltage targets as long as you can tolerate 3.2V on your data bus,
your target provides logic highs of at least 1.5V and our low voltage cut-off circuit does not kick-in.
How accurate are FlexROM III’s voltage readings?
The readings are typically accurate to +- 250mv.
Can FlexROM III emulate FLASH devices?
The emulator supports FLASH pin-outs and accepts target writes. However, it does NOT emulate any of
the special FLASH algorithms. For example, it does not support the special sequences that lock/unlock
pages of memory or any kind of busy indicators. It operates at full speed and looks like SRAM to the
target.
FlexROM III User’s Manual
32
Copyright ? 2001, TechTools
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B7W-EY-F4 | CONVERTER MOD DC/DC 5.5V 50W |
| TC1270AMVCTTR | IC RESET MONITOR 4.38V SOT23A-5 |
| VE-B7W-EY-F3 | CONVERTER MOD DC/DC 5.5V 50W |
| TC1270ALVRCTR | IC RESET MONITOR 4.63V SOT143-4 |
| VE-B7W-EY-F2 | CONVERTER MOD DC/DC 5.5V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FR3A | 制造商:SEMIKRON 制造商全称:Semikron International 功能描述:Fast silicon rectifier diodes |
| FR3A_06 | 制造商:WTE 制造商全称:Won-Top Electronics 功能描述:3.0A SURFACE MOUNT GLASS PASSIVATED FAST RECOVERY DIODE |
| FR3A_07 | 制造商:SEMIKRON 制造商全称:Semikron International 功能描述:Fast silicon rectifier diodes |
| FR3A_09 | 制造商:PANJIT 制造商全称:Pan Jit International Inc. 功能描述:FAST SWITCHING SURFACE MOUNT RECTIFIER |
| FR3A_11 | 制造商:MCC 制造商全称:Micro Commercial Components 功能描述:3 Amp Fast Recovery Silicon Rectifier 50 to 1000 Volts |
发布紧急采购，3分钟左右您将得到回复。