- 您现在的位置：买卖IC网 > PDF目录11822 > FT2232HL-TRAY (FTDI, Future Technology Devices International Ltd)IC USB HS DUAL UART/FIFO 64-LQFP PDF资料下载
参数资料
| 型号： | FT2232HL-TRAY |
| 厂商： | FTDI, Future Technology Devices International Ltd |
| 文件页数： | 14/67页 |
| 文件大小： | 0K |
| 描述： | IC USB HS DUAL UART/FIFO 64-LQFP |
| 标准包装： | 160 |
| 系列： | USBmadeEZ-FIFO，FT-X，X-Chip |
| 特点： | USB 至 UART 和（或）FIFO、SPI、I2C、JTAG |
| 通道数： | 2，DUART |
| FIFO's： | 4096 字节 |
| 规程： | RS232，RS422，RS485 |
| 电源电压： | 3 V ~ 3.6 V |
| 带并行端口： | 是 |
| 带自动流量控制功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-LQFP |
| 包装： | 托盘 |
| 其它名称： | FT2232HL - TRAY |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页
Copyright 2012 Future Technology Devices International Limited
21
Document No.: FT_000061
FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC
Version 2.21
Clearance No.: FTDI#77
provide fine tuning of the baud rate (used to divide by a number plus a fraction). This determines the
Baud Rate of the UART which is programmable from 183 baud to 12 million baud. The FT2232H does not
support the baud rates of 7 Mbaud 9 Mbaud, 10 Mbaud and 11 Mbaud.
See FTDI application note AN232B-05 on the FTDI website (www.ftdichip.com) for more details.
+1.8V LDO Regulator. The +1.8V LDO regulator generates the +1.8 volts for the core and the USB
transceiver cell. Its input (VREGIN) must be connected to a +3.3V external power source. It is also
recommended to add an external filtering capacitor to the VREGIN. There is no direct connection from the
+1.8V output (VREGOUT) and the internal functions of the FT2232H. The PCB must be routed to connect
VREGOUT to the pins that require the +1.8V including VREGIN.
UTMI PHY. The Universal Transceiver Macrocell Interface (UTMI) physical interface cell. This block
handles the Full speed / High Speed SERDES (serialise – deserialise) function for the USB TX/RX data. It
also provides the clocks for the rest of the chip. A 12 MHz crystal should be connected to the OSCI and
OSCO pins. A 12K Ohm resistor should be connected between REF and GND on the PCB.
The UTMI PHY functions include:
Supports 480 Mbit/s “High Speed” (HS)/ 12 Mbit/s “Full Speed” (FS), FS Only and “Low Speed”
(LS)
SYNC/EOP generation and checking
Data and clock recovery from serial stream on the USB.
Bit-stuffing/unstuffing; bit stuff error detection.
Manages USB Resume, Wake Up and Suspend functions.
Single parallel data clock output with on-chip PLL to generate higher speed serial data clocks.
EEPROM Interface. When used without an external EEPROM the FT2232H defaults to a USB to dual
asynchronous serial port device. Adding an external 93C46 (93C56 or 93C66) EEPROM allows each of the
chips channels to be independently configured as a serial UART (RS232 mode), parallel FIFO (245) mode
or fast serial (opto isolation). The external EEPROM can also be used to customise the USB VID, PID,
Serial Number, Product Description Strings and Power Descriptor value of the FT2232H for OEM
applications. Other parameters controlled by the EEPROM include Remote Wake Up, Soft Pull Down on
Power-Off and I/O pin drive strength.
The EEPROM should be a 16 bit wide configuration such as a Microchip 93LC46B or equivalent capable of
a 1Mbit/s clock rate at VCC = +3.00V to 3.6V. The EEPROM is programmable in-circuit over USB using a
utility program called MPROG available from FTDIs web site (www.ftdichip.com). This allows a blank
part to be soldered onto the PCB and programmed as part of the manufacturing and test process.
If no EEPROM is connected (or the EEPROM is blank), the FT2232H will default to dual serial ports. The
device uses its built-in default VID (0403) , PID (6010) Product Description and Power Descriptor Value.
In this case, the device will not have a serial number as part of the USB descriptor.
相关PDF资料 |
PDF描述 |
|---|---|
| SC28L92A1A,512 | IC UART DUAL W/FIFO 44-PLCC |
| VI-B5B-IY | CONVERTER MOD DC/DC 95V 50W |
| D38999/20WD19PC | CONN RCPT 19POS WALL MNT W/PINS |
| ATMEGA169PV-8MCHR | MCU AVR 16KB FLASH 16MHZ 64QFN |
| MS27484T16B8PA | CONN PLUG 8POS STRAIGHT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FT2232HMINIMODULE | 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB Hi-Speed FT2232H Evaluation Module 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB to serial/FIFO development module |
| FT2232H-MINI-MODULE | 制造商:Future Technology Devices International (FTDI Chip) 功能描述:IC,EVALUATION MODULE;FT2232H;USB HI-SPEED |
| FT2232HQ | 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB Hi-Speed to Dual Channel Serial UART/FIFO/JTAG/SPI/I2C IC - QFN-64 |
| FT2232HQ_MINI_ MODULE | 功能描述:界面开发工具 USB Hi-Speed FT2232H Evaluation Module RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| FT2232HQ-4000 | 制造商:FTDI 制造商全称:FTDI 功能描述:DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC |
发布紧急采购，3分钟左右您将得到回复。