- 您现在的位置：买卖IC网 > PDF目录11822 > FT2232HL-TRAY (FTDI, Future Technology Devices International Ltd)IC USB HS DUAL UART/FIFO 64-LQFP PDF资料下载
参数资料
| 型号： | FT2232HL-TRAY |
| 厂商： | FTDI, Future Technology Devices International Ltd |
| 文件页数： | 5/67页 |
| 文件大小： | 0K |
| 描述： | IC USB HS DUAL UART/FIFO 64-LQFP |
| 标准包装： | 160 |
| 系列： | USBmadeEZ-FIFO，FT-X，X-Chip |
| 特点： | USB 至 UART 和（或）FIFO、SPI、I2C、JTAG |
| 通道数： | 2，DUART |
| FIFO's： | 4096 字节 |
| 规程： | RS232，RS422，RS485 |
| 电源电压： | 3 V ~ 3.6 V |
| 带并行端口： | 是 |
| 带自动流量控制功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-LQFP |
| 包装： | 托盘 |
| 其它名称： | FT2232HL - TRAY |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页
Copyright 2012 Future Technology Devices International Limited
13
Document No.: FT_000061
FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC
Version 2.21
Clearance No.: FTDI#77
3.4.2 FT2232H pins used in an FT245 Style Synchronous FIFO Interface
The FT2232H only channel A can be configured as a FT245 style synchronous FIFO interface. When
configured in this mode, the pins used and the descriptions of the signals are shown in Table 3.5. To
enter this mode the external EEPROM must be set to make port A 245 mode. A software command (Set
Bit Mode option) is then sent by the application to the FTDI driver to tell the chip to enter single channel
synchronous FIFO mode. In this mode the B channel is not available as all resources have been switched
onto channel A. In this mode, data is written or read on the rising edge of the CLKOUT.
Channel A
Pin No.
Name
Type
FT245 Configuration Description
24,23,22,21,
19,18,17,16
ADBUS[7:0]
I/O
D7 to D0 bidirectional FIFO data. This bus is normally input unless
OE# is low.
26
RXF#
OUTPUT
When high, do not read data from the FIFO. When low, there is data
available in the FIFO which can be read by driving RD# low. When in
synchronous mode, data is transferred on every clock that RXF# and
RD# are both low. Note that the OE# pin must be driven low at least
1 clock period before asserting RD# low.
27
TXE#
OUTPUT
When high, do not write data into the FIFO. When low, data can be
written into the FIFO by driving WR# low. When in synchronous
mode, data is transferred on every clock that TXE# and WR# are both
low.
28
RD#
INPUT
Enables the current FIFO data byte to be driven onto D0...D7 when
RD# goes low. The next FIFO data byte (if available) is fetched from
the receive FIFO buffer each CLKOUT cycle until RD# goes high.
29
WR#
INPUT
Enables the data byte on the D0...D7 pins to be written into the
transmit FIFO buffer when WR# is low. The next FIFO data byte is
written to the transmit FIFO buffer each CLKOUT cycle until WR# goes
high.
32
CLKOUT
OUTPUT
60 MHz Clock driven from the chip. All signals should be synchronized
to this clock.
33
OE#
INPUT
Output enable when low to drive data onto D0-7. This should be
driven low at least 1 clock period before driving RD# low to allow for
data buffer turn-around.
30
SIWU
INPUT
The Send Immediate / WakeUp signal combines two functions on a
single pin. If USB is in suspend mode (PWREN# = 1) and remote
wakeup is enabled in the EEPROM , strobing this pin low will cause the
device to request a resume on the USB Bus. Normally, this can be
used to wake up the Host PC.
During normal operation (PWREN# = 0), if this pin is strobed low any
data in the device TX buffer will be sent out over USB on the next
Bulk-IN request from the drivers regardless of the pending packet
size. This can be used to optimize USB transfer speed for some
applications. Tie this pin to VCCIO if not used. (Also see note 1, 2, 3
in section 4.12)
Table 3.5 Channel A FT245 Style Synchronous FIFO Configured Pin Descriptions
For a functional description of this mode, please refer to section 4.4
相关PDF资料 |
PDF描述 |
|---|---|
| SC28L92A1A,512 | IC UART DUAL W/FIFO 44-PLCC |
| VI-B5B-IY | CONVERTER MOD DC/DC 95V 50W |
| D38999/20WD19PC | CONN RCPT 19POS WALL MNT W/PINS |
| ATMEGA169PV-8MCHR | MCU AVR 16KB FLASH 16MHZ 64QFN |
| MS27484T16B8PA | CONN PLUG 8POS STRAIGHT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FT2232HMINIMODULE | 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB Hi-Speed FT2232H Evaluation Module 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB to serial/FIFO development module |
| FT2232H-MINI-MODULE | 制造商:Future Technology Devices International (FTDI Chip) 功能描述:IC,EVALUATION MODULE;FT2232H;USB HI-SPEED |
| FT2232HQ | 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB Hi-Speed to Dual Channel Serial UART/FIFO/JTAG/SPI/I2C IC - QFN-64 |
| FT2232HQ_MINI_ MODULE | 功能描述:界面开发工具 USB Hi-Speed FT2232H Evaluation Module RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| FT2232HQ-4000 | 制造商:FTDI 制造商全称:FTDI 功能描述:DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC |
发布紧急采购，3分钟左右您将得到回复。